Model #9587 SHARP Countertop Microwave

  • Microwave Service Manual/front Cover
    3 Results
  • Information
    3 Results
  • Information Page 2
    3 Results
  • Information Page 3
    3 Results
  • Information Page 4
    3 Results
  • Information Page 5
    3 Results
  • Information Page 6
    3 Results
  • Information Page 7
    3 Results
  • Information Page 8
    3 Results
  • Information Page 9
    3 Results
  • Information Page 10
    3 Results
  • Information Page 11
    3 Results
  • Information Page 12
    3 Results
  • Information Page 13
    3 Results
  • Information Page 14
    3 Results
  • Information Page 15
    3 Results
  • Information Page 16
    3 Results
  • Information Page 17
    3 Results
  • Information Page 18
    3 Results
  • Information Page 19
    3 Results
  • Information Page 20
    3 Results
  • Information Page 21
    3 Results
  • Information Page 22
    3 Results
  • Schematic Diagram
    3 Results
  • Wiring Diagram
    3 Results
  • Control Panel Curcuit
    3 Results
  • Control Panel Curcuit Page 2
    3 Results
  • Printed Wiring Board
    3 Results
  • Complete Microwave Assembly
    3 Results
  • Complete Microwave Assembly Page 2
    3 Results
  • Complete Microwave Assembly Page 3
    3 Results
  • Complete Microwave Assembly Page 4
    3 Results
  • Complete Microwave Assembly Page 5
    3 Results
  • Complete Microwave Assembly Page 6
    3 Results
  • Microwave Oven/front Cover
    3 Results
  • Information
    3 Results
  • Information Page 2
    3 Results
  • Information Page 3
    3 Results
  • Information Page 4
    3 Results
  • Information Page 5
    3 Results
  • Information Page 6
    3 Results
  • Information Page 7
    3 Results
  • Information Page 8
    3 Results
  • Information Page 9
    3 Results
  • Information Page 10
    3 Results
  • Information Page 11
    3 Results
  • Information Page 12
    3 Results
  • Information Page 13
    3 Results
  • Information Page 14
    3 Results
  • Information Page 15
    3 Results
  • Information Page 16
    3 Results
  • Information Page 17
    3 Results
  • Information Page 18
    3 Results
  • Information Page 19
    3 Results
  • Information Page 20
    3 Results
  • Information Page 21
    3 Results
  • Information Page 22
    3 Results
  • Schematic Diagram
    3 Results
  • Complete Microwave Assembly
    3 Results
  • Complete Microwave Assembly Page 2
    3 Results
  • Complete Microwave Assembly Page 3
    3 Results
  • Complete Microwave Assembly Page 4
    3 Results
  • Complete Microwave Assembly Page 5
    3 Results
  • Complete Microwave Assembly Page 6
    3 Results
  • Complete Microwave Assembly Page 7
    3 Results
  • Complete Microwave Assembly Page 8
    3 Results
  • Complete Microwave Assembly Page 9
    3 Results
  • Complete Microwave Assembly Page 10
    3 Results
Find part by diagram >

Question and Answers

Q:

Kenmore Elite Dryer reset button

A:

I know this type of information can be very helpful for you to have.  While you are waiting for your expert answer, I did some research on the dryer.  I was unable to locate information that would be helpful with regards to your question at this time.  Your expert will answer within two business days.  I also added the link to Sears Home Services, if you decide to schedule service.  Thank you for using Manage My Life.
 

Read More
Yadira B -
June 11, 2013
A:

Thank you for your question and I understand your concern.

There is not any internal reset buttons on the dryer. If the control panel is not powering up or displaying "PF" when it's plugged in, and the dryer is getting the proper power supply, then it could have a faulty machine control board or possibly a shorted User Interface/Control panel assembly.

Diagnosing the failure will require making voltage measurements and the testing of the User Interface/Control panel button operation using an Ohm meter. NOTE: I do not recommend making any voltage measurements unless you have experience and feel safe and confident in doing so, otherwise I strongly suggest calling a service technician with the training and experience to properly diagnose and repair your dryer. 

I added an image below a technician would use to diagnose the failure. I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post along with the complete model number read off the model and serial number tag on the dryer. 

 If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services.

 

 

 

Read More
Joey S -
Sears Technician
June 12, 2013
See more answers
Q:

HOT WATER ONLY WASH ON MAYTAG WASHER MODEL: MAV 7000 AWN

A:

Hawaii seems to be a very beautiful and relaxing place to live. I'm sure your washer problems aren't contributing to the relaxing experience you get to sometimes enjoy. Upon researching your question I found a couple links that may help you with your situation. I hope these links are helpful!

Read More
Jackie S -
March 24, 2011
A:

Thank you for your question.

I can understand your frustration with only getting hot water not matter what you do.

We first need to find out if the cold water works at all?

Have you tried switching the orange and blue wires on the water valve?

If the cold water does not work at all then I would conclude the water valve is bad.

If the cold water works when you switch the wires then I would conclude that the analog temp control on the back of the timer is the most likely problem.

The part number for the control is: 22003906.

I hope this will help.

Thank you for using Manage My Life.

Read More
Sam A -
Sears Technician
March 24, 2011
A:

Aloha Sam.. I refer to your excellent reply to my problem & I answer you in kind: 1) The cold water indeed works perfectly well... (Just not on the wash cycle!.. The wash cycle is HOT and the rinse cycle is cold. This shows us the the cold water does indeed function). FYI, the water flow fills normally during both the wash and rinse cycle. The only problem is my ability to choose hot or cold during the wash. The rinse is perfectly acceptable with cold as I never rinse with hot anyway. 2) I did switch the wires on the TEMP CONTROL SWITCH (I dont recall the colors, but know that is did switch them) and this resulted in no difference. The same hot water came in during the wash cycle. 3) If you are correct and it is the analog control on the back of the timer (part #: 22003906) are you referring to what I call & looks like the Mother Circuit Board??? Would you suggest with the new details/info I have provide you today that I make that my next step??? I am willing to do so upon your confirmation. 4) Another Gentleman (Jackie S) replied with a link (http://www.managemylife.com/mmh/questions/110292-washer-fill-cold-water) which suggests that I may have a bad temperature selector switch, a bad solenoid valve, failed wiring contacts or a wiring problem.. Do any of these items warrant our interest? before purchasing the new analog control?? Again Sam , Many thanks for your very valuable guidance & help. Standing by, Gilbert

Read More
Gilbert Garcia -
March 24, 2011
A:

Thank you for the update. Now that I know that the cold water is working normally I am fairly sure that the Electronic temp control on the back of the timer is the problem. My only concern is the thermistor in the water valve, reference #47 in the image below and it goes to the GY connections on the temp control part number: 22003906. There does not seem to by any information on a good way to test the thermistor. View the image below. I would go with replacing the Temp Control. I am confident that you will solve this problem. Thank you for using Manage My Life. Sam A.

Read More
Sam A -
Sears Technician
March 25, 2011
A:

Aloha again Sam, Thanks for the final confirmation. I will now proceed and start the authorized return the Timer unit and request the new Temp Control part. I will then install and hope for the best. I will revert to you once again should there be more problems. But until then, thanks a million. Over and out for this round... Regards, Gilbert

Read More
Gilbert Garcia -
March 25, 2011
A:

Aloha yet again Sam, I called the Parts Dept. to order the new part (as per your info: a Temp Control with part number: 2200-3906) and now they tell me they don't have the part number in their system,plus they don't even know the part number you mention nor does the number match up with anything they have on file??? The only thing they can provide me with for my Maytag Washer is a: TEMP CONTROL SWITCH = #2200-2936 @ $36.71 . What do I do? Is their number the same part as what you are suggesting? Again, with a $40 shipping cost per each adventure, I do not wish to experiment with mystery part numbers. Standing by and thanking you. Gilbert

Read More
Gilbert Garcia -
March 25, 2011
A:

26 464 22003906 ANALOG TEMP 1 27.79 27.79 I have pasted the information from the parts list . The original part number was 222002857and now subs to 22003906. I hope this will help. Sam A.

Read More
Sam A -
Sears Technician
March 25, 2011
A:

Aloha Sam, I have delayed my answer and thanks to you until this moment. I received the Analog Temp part, installed it, and much to my delight, all is now good... The cold water is flowing!!! Again, I deeply appreciate your guidance and this project is ofcially over!!!... Until the next one!!! Mahalo as they say over here!!! Regards, Gilbert

Read More
Gilbert Garcia -
March 31, 2011
A:

Hi Sam, I have the same problem like what Gilbert has described from the above message. My Maytag MAV6200AWW that we purchased from July 2002. there are several issues with the washer. 1) When I select other buttons than WARM/COLD, then the washer can't start at all. I must select the WARM/COLD button to turn on the washer. The water is steaming hot and it is not usual for WARM/COLD selection. 2) It stops in middle in the RINSE cycle. We have to adjust the RINSE cycle differently to make it run again and it still could not complete the cycle back to OFF position. The clothes were dried and looked clean. Please let us know if it is possible to fix the issues or it is time to buy another washer if the cost to fix it is too high. Thanks for your help.

Read More
minh -
October 06, 2012
A:

Thank you for your question Minh. I think that you may have two problems with the washer. The stopping in mid-cycle could be the lid switch connections and if you put the washer in a spin cycle and wiggle the lid switch harness and it stops and starts then the lid switch will need to be replaced. The other problem sounds like the cold solenoid on the water valve is not working. If you feel comfortable with using a volt/ohm meter you can check the circuit I will send you in the image below to determine if the water valve is the problem. If the lid switch proves to be bad then the part will cost about $25.00. If you also have to change out the water valve then the price of the water valve is about $35.00. Please let me know what you find out. Sam A.

Read More
Sam A -
Sears Technician
October 08, 2012
See more answers
Q:

White clothes with scorch marks.Kn

A:

When your dryer is ruining your clothes instead of drying them it is a huge disappointment. I was able to find a link that includes great information for your specific model. I attached the link below. I hope this is helpful.

Read More
Jackie S -
July 20, 2012
A:

I'm sorry about the marks on the whites. Has this been a problem since day one or has the problem recently started. You say scorch marks are getting on the clothes. I'm not sure if you have a gas or electric dryer but I suspect the problem is the felt drum seal. If the seal fails then clothes can get caught between the drum and bulkhead and become marked up. You can remove the top to take a look at the drum and felt seal. The image below will help you do this. Use caution when the dryer is running with the top panel removed. I hope this helps. You can reply with any additional details or questions for further assistance.

Read More
Fred M -
Sears Technician
July 21, 2012
See more answers