Model #92116475 CRAFTSMAN Air compressor

  • Regulator
    3 Results
  • Compressor
    3 Results
  • Pump Asy
    3 Results
Find part by diagram >

Question and Answers

Q:

Can the tank safety relief valve (part # 136-0104) lift pressure be adjusted? 92116475 Craftsman Compressor

A:

Thanks for the inquiry and for being a valued member.

I see the cut-out at 150 PSI, so you're right, the safety valve is kicking in prematurely. There isn't an adjustment for the valve, so it will need to be replaced. It is common for a safety valve to leak or trip prematurely when they are in need of replacement. The safety valve will not be adjustable. 

I hope this helps and thanks for using SearsPartsDirect.com. We appreciate your business. 

Read More
Jeff Wallace Sr -
Sears Technician
July 29, 2015
Q:

blows circuit breaker

A:

I can understand your concern. Maybe something is arching within the circuitry. But it would be very helpful if you could let us know what type of appliance or tool this is. A complete model number would be great too. Please respond to this thread and include any other details and symptoms you might be experiencing. Until we hear from you, have a nice day.

Read More
Henry -
July 08, 2013
A:

craftsman professional 92116475

Read More
Gary -
July 08, 2013
A:

Also this compressor after break in period may have been ran 10 times

Read More
Gary -
July 08, 2013
A:

Thank you for your question.

I can understand wanting to know why the compressor is tripping the circuit breaker.

I would like to get a little more information from you.

Do you have the compressor on a dedicated 15 amp slo-blow circuit?

Have you tried plugging it into a different circuit to see if it works and this would eliminate the regular circuit that it is on?

Is the compressor tripping the circuit breaker as soon as you turn it on or does it run for a few seconds before it trips the breaker?

If this is the case the un-loader valve may not be unloading the head pressure from the head on restart.

When and if you can get it to run did you hear a whoosh sound for a few seconds as it shuts off?

It could also be a start capacitor on the motor has failed and the motor cannot start.

Does the thermal overload on the motor trip?

If you would like more assistance, reply to this thread with more details and I will assist you further.

 

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services.  

 

Read More
Scott D -
Sears Technician
July 10, 2013
A:

I have taken care of the problem myself, who ever at Sears put this compressor together had the belt so tight the motor would not start. Loosened the belt a bit and have no problems now.

Read More
Gary -
July 10, 2013
A:

Gary, thank you for the information and for using Manage My Life.

Read More
Scott D -
Sears Technician
July 11, 2013
See more answers
Q:

change air compressor from 110V to 220V need wiring diagram

A:

I think its great that you are wanting to do some repairs on your own. I am adding a link below to help you with your project while you wait for your expert response.

Read More
Joseph P. -
January 28, 2012
A:

Remove the cap to the pressure switch and see if the schematic for 220VAC wiring is shown there. If it's not (and it's often not), remove the access plate on the back of the motor (near where the wire goes in) and the schematic will for the wiring will be on that plate.

The schematic is not shown in the manual due to variances in manufacturing for the pressure switch and motors.

Thank you for using Manage My Life!

Read More
XX Wade_ -
Sears Technician
January 30, 2012
A:

OK, schematic for the MOTOR is on the motor label. That looks straightforward. What about bring 220V into the pressure switch? The wiring goes from the cord to the switch and then the switch to the motor. As far as a cord, I assume I will have to supply my own.... couldnt find any 220v cord available from sears.

Read More
dave -
January 30, 2012
A:

Yes, you will need to supply the power cord for that. The pressure switch will have 110 on L1 and L2. Whereas right now there is 110 on one or the other and "return" (white) wire on the other. When running 220VAC, there is no "return" wire.

Read More
XX Wade_ -
Sears Technician
January 30, 2012
See more answers

Top Parts

Top Accessories