Model #9200 BISSELL Power Steamer

  • Upright Deep Cleaner
    3 Results
Find part by diagram >

Question and Answers

Q:

Hover Steam Vac Model F5862900 F5862900 Hoover Steam vac-upright

A:

Our apologies, but Sears no longer has the replacement hose available. There is a seller on ebay showing that he has more than 10 available, or you may call Hoover at (800) 944-9200 for more information.

Read More
Ernest7574 -
Sears Technician
November 21, 2015
A:

Thanks for your "quick" response to my question. Only a little over a month! Just as I've come to expect from this faltering company.

Read More
Larry -
November 21, 2015
See more answers
Q:

My Duet dryer Has an Error Code F01

A:

A Washer is definitely something we depend on and when it begins to malfunction it can be a huge inconvenience. While you are waiting for an expert to respond, I have attached some helpful links below that may provide information to assist you with your question.

Read More
Priscilla V -
January 03, 2012
A:

I see Pvalde2 provided you with good information however, it does not pertain to a dryer. The F-01 error code indicates a primary control board failure on this model of dryer. If the error cleared after unplugging it for 20-30, then the control board could have received a power surge or glitch through the electrical lines. Completely disconnecting the electrical power and then reconnecting it will sometimes reset the board and it will operate properly. If your dryer continues to operate properly, then resetting the control board may have fixed your problem.

If the dryer motor continues to stop working, then you may have a bad control board. A wiring problem or drive motor failure could also prevent the dryer from continuing to run properly. A technician is normally needed to diagnose and repair this type of problem. If the F-01 returns and will not clear, then you will need to replace the control board in the dryer.

If you do not feel comfortable repairing the unit yourself, service can be scheduled at the following link: Sears Home Services . For further assistance, please respond to this thread with more detail. I hope this helps.

Read More
Korinna S -
Sears Technician
January 05, 2012
A:

Is it easy to replace the control board?

Read More
lisa -
September 17, 2012
A:

Please be sure to unplug the dryer prior to attempting any service or repair. I have included the instructions from the service manual that explain the process. Look it over and if you do not feel comfortable performing the task, service can be scheduled at the Sears Home Services link I provided above. For further assistance, please respond to this thread. I hope this helps.

Read More
Korinna S -
Sears Technician
September 18, 2012
A:

What would be part number for control board, where can I get one, and finially how much?

Read More
Sam -
November 14, 2012
A:

Hello Sam. WED9400SU is a partial model number that brings up 3 models. Two of the model have the same part number for the control board, while the other is different. Once you have the complete model number of your specific model, you can search for the part and purchase it from Sears PartsDirect. The diagram you want to be looking at is the "Dryer Cabinet" diagram. The control board you need is number 41 on the diagram. I really hope this information helps you today. For further assistance, please respond to this thread. I will be delighted to assist you. Thank you for using ManageMyLife.com

Read More
Korinna S -
Sears Technician
November 16, 2012
A:

I have a whirlpool duet sport gas model number WGD8300SW1, It started with F-1 error code, I checked control board and it had burn mark, so I changed it. the F-1 code is gone but I have NO heat. I take any help!

Read More
Sam -
November 24, 2012
A:

Hey there Korinna, the images you provided above are really small, can you please repost larger images?

Read More
clipper -
April 12, 2015
A:

i have a whirlpool duet dryer model number 4WED9200SQ1 i get an error message F1 what can i do myself to fix this please and thank u i put some clothes in it shut the door and it did start but then stopped and i heard a click sound then got the error i went to the fuse box and clicked it on and off and nothing it still wont work is there anyway i can do it myself at home appreciate any help u can give me thank u

Read More
denise -
May 25, 2015
A:

Hello, I have a Whirlpool dryer model Wgd8300sw1 that is giving me error code F-01. It does not clear when the unit is power cycled. Does the main control board need to be replaced, part number W10111606? Or what is the solution? Thank you.

Read More
Steven -
November 16, 2015
See more answers
Q:

Dryer not heating. GEW9200LW1


Top Parts