Model #919762350 CRAFTSMAN Power Washer

  • Replacement Parts
    3 Results
  • Pump Breakdown Pk16482
    3 Results
Find part by diagram >

Question and Answers

Q:

Oil drain plug location 919762350 Craftsman Pressure washer

A:

Dear Frustrated, 

Thank you for choosing Sears and for contacting us with your question about the location of oil drain plug on your Craftsman pressure washer model 919762350. I am so sorry you are having trouble locating it.  I will be happy to help you with this. I have included the link below for you to view the owner’s manual online because it sounds like you may have the wrong manual. 

Under the engine maintenance instructions on page 12, the manufacturer states that the preferred method of draining the oil is from the top of the engine. There is an illustration showing which way the engine should be tipped. However, since you prefer to drain the oil from the bottom of the engine, that information is also provided. There is a drawing of the drain plug on that page. To locate the oil drain plug you will need to look at the bottom of the engine sump. Please view page 20 of the manual. The sump is reference 4 in the diagram. If you look inside of the box in the lower right corner the drain plug is reference key 15. I have included the link below for you to view a picture of the drain plug so you will know what to look for on the sump.

SAFETY WARNING: Make sure to follow the safety precautions in your owner’s manual when completing this maintenance. If you would prefer to have a technician complete the maintenance for you, you can set up service at www.SearsHomeServices.com or by calling 1-800-469-4663. 

I hope this answers your question. Thank you for choosing Sears, we appreciate your business. 
 

Read More
Rachel Morgan -
Sears Technician
July 11, 2015
Q:

Craftsman Pressure washermodel #919762350 not dispensing soap. No suction in tube. 919762350 Craftsman Pressure washer

A:

Thank You for choosing Sears PartsDirect.com. I regret to hear that you are having issues with your pressure washer and do understand your frustration. Glad to help out. Im looking at your model number 919762350 and there is a check ball and a string under the fitting that the hose for the soap solution attaches to. If the check ball gets stuck it will not open to siphon the soap solution into the water stream. It is a brass nipple fitting and if you remove that make sure you do not loose the spring or the little steel ball. As you know the soap solution can only be drawn into the stream during the low pressure position on the wand. Please make sure the orifice is completely clean. The pressure washer will only draw soap during on the low pressure setting on the wand. If you are trying to draw soap on the high pressure position it will not work. I do not think the spring be gone would prevent the soap not to draw into the water flow. Please make sure that your nozzle orifice is clean and I would suggest that you remove the inline screen between the wand handle and the nozzle tube because it may be causing enough restriction for the soap not to draw. 
Also make sure that the check ball is not stuck against the seat and will not open. The spring is just a guide for the check ball. The high pressure setting is what keeps it closed and the low pressure setting draws the check ball away from the seat. If you have further questions please resubmit your question for further information.

 
Thank you for choosing Sears PartsDirect.com.

Read More
Sherman_G_Wallace -
Sears Technician
May 21, 2014
A:

I need to replace that fitting including ball n spring. Where can I purchase? I have one of these models and noticed that it wouldn't draw the Chemical either and while shopping for a new piece I dropped the it and out rolls the ball.... Lost it and now I can't find where I can buy this essential part. I'm Very frustrated so please help.

Read More
Chad -
June 25, 2015
See more answers
Q:

I have very little water presure What can I do 919762350 Craftsman Pressure washer

A:

Thank you for choosing SearsPartsDirect.com. I will be more then happy to assist you. If you are not getting any pressure, I recommend cleaning the hole in the nozzle at the end of the wand. If it is plugged, it will hold the unloader valve open and the pump will not build pressure. If cleaning the nozzle does not help, I suspect the unloader valve is stuck open. Lime and minerals building in the pump cause this. You can try to remove the unloader and clean the parts to see if it helps. I posted an image below that show the parts of the unloader valve. Just click on the image to enlarge it. Once you have the unloader out use WD-40 and Scotch brite pad to clean the parts. After you have them clean, reassemble the unit and check the operation. If it still does not work, I recommend replacing the unloader. Hope this information has help you. If you are not comfortable doing this repair you can Click Here to schedule a technician or call toll free 1-800-469-4663. Any further questions or concerns. You will have to post a new question because at this time I can not reply to any comments. Again, Thank you for choosing SearsPartsDirect.com.
 

Read More
Samantha A -
Sears Technician
June 27, 2014