Model #917251550 CRAFTSMAN Lawn, Tractor

  • Electrical
    3 Results
  • Chassis And Enclosures
    3 Results
  • Ground Drive
    3 Results
  • Steering Assembly
    3 Results
  • Engine
    3 Results
  • Seat Assembly
    3 Results
  • Decals
    3 Results
  • Wheels And Tires
    3 Results
  • Lift Assembly
    3 Results
  • Mower Deck
    3 Results
  • Transaxle
    3 Results
  • Engine Cv22s-67515 (71,501)
    3 Results
  • Engine Cv22s-67515 (71,501)
    3 Results
  • Engine Cv22s 67515 (71,501)
    3 Results
  • Engine Cv22s 67515 (71,501)
    3 Results
  • Engine Cv22s-67515 (71,501)
    3 Results
  • Engine Cv22s-67515 (71,501)
    3 Results
  • Engine Cv22s-67515 (71,501)
    3 Results
  • Engine Cv22s-67515 (71,501)
    3 Results
  • Engine Cv22s-67515 (71,501)
    3 Results
  • Engine Cv22s-67515 (71,501)
    3 Results
  • Engine Cv22s-67515 (71,501)
    3 Results
Find part by diagram >

Question and Answers

Q:

Mower starts, but will not keep running. Fuel pump seems to be working. What is it? 917251550 Craftsman Tractor

A:

Thanks for the inquiry and for being a valued member.

I am sorry to hear of the issue you’re having with the tractor. I know how frustrating that is.

This sounds like a fuel issue, and I would suspect that the carburetor has an internal blockage in the fuel jet or one of the passageways. I would pull the carb from the engine. With a full can of carb cleaner, a wire brush, and a bread tie wire to poke through and clean the main jet; I would recommend a very thorough cleaning. Start by taking off the float bowl. Douse it very liberally with carb cleaner, and undo the pin for the float, and remove the needle and float. Clean them very thoroughly with the wire brush and carb cleaner. Pay close attention to the seat the needle sits in and clean it well. Once clean, start brushing the carb bowl and body and make sure you get all the varnish out. It may take three or four brushings with carb cleaner dousing in-between. From there, take the straw of the carb cleaner and shoot carb cleaner through any little hole or passageway of the carb. Shoot out the throat of the carb and poke the main jet with the bread tie wire. You have to make sure you get everything the first time, if you leave anything behind, it’s likely to reclog once you have it reassembled. 

I hope this helps and thanks for using SearsPartsDirect.com. We appreciate your business. 

Read More
Jeff Wallace Sr -
Sears Technician
June 28, 2015
Q:

will not move 917251550 Craftsman Tractor

A:

Thanks for the inquiry and for using SearsPartsDirect.com. 

Sorry to hear of the issue you're having with the transaxle not going into gear, I know how frustrating that is to have occur.

Before deciding to replace the transaxle, I have a few suggestions to try:

The first question is have you removed the rear wheels. The rear wheels have a square axle key that drive them. If the wheels were taken off, the key may have likely fell on the ground, and without it in place, the wheels will not spin. 

If the axle key is in position, the next check to make is if the drive belt is still on. With the tractor on a level surface and the engine off look under the tractor at the drive belt. The belt should be free of slack and go around all of the pulleys.

Next check the brake lever on the transaxle. If it has been sitting for a long period of time it might be stuck on. The lever is located on the right side of the tractor inside of the frame. I recommend working the lever back and forth to make sure it is moving freely. It might be a good idea to give it a couple of shots of WD40.

When you are looking under the tractor, have someone move the shifter. When the shifter is moved, you should see the shifter on the transaxle move. If the shifter is properly attached, have someone start the tractor and let out on the brake. Now carefully look under the tractor at the transaxle drive pulley. The drive pulley should be spinning. If the pulley is spinning, the problem is most likely a defective transaxle. If the transaxle is defective, the replacement transaxle is still available and the part number is 184956. 

I would imagine your issue will fall within one of the suggestions above. Hope these help out and thanks for using SearsPartsDirect.com. We appreciate your business. 


 

Read More
Jeff Wallace Sr -
Sears Technician
July 15, 2014
Q:

Snow thrower assembly schematic 917251550

A:

Thank you for contacing SearsPartsDirect.com with your question about the snow thrower attachment for your Craftsman riding tractor. Having the right model number is important when looking for parts. I will be happy to help you with this. 

Since more than one snow thrower may fit your model, it is always best to get the model number off of the snow thrower itself. The model number will normally be on a label on the back of the auger housing or on the bracket attaching the snow thrower to the tractor.

If you purchased the snow thrower made specifically for your tractor, it is a 42" - 2 stage snow thrower attachment with the model number 486.24837. I have included the link for you to view the owner's manual for this model online. The manual will include the parts diagrams and the part numbers. 

Owner's Manual for Snow Thrower Attachment 48624837.

I hope this answers your questions. If you need further assistance, please resubmit your question with additional details. Thank you for choosing Sears, we appreciate your business. 

Read More
Rachel Morgan -
Sears Technician
February 22, 2014

Top Parts