Model #91199002990 KENMORE Free Standing, Electric

  • Backguard(91199003990)
    3 Results
  • Backguard
    3 Results
  • Body
    3 Results
  • Maintop
    3 Results
  • Wire Harness And Components
    3 Results
  • Door
    3 Results
  • Door (91199003990)
    3 Results
  • Lock And Fan
    3 Results
Find part by diagram >

Question and Answers

Q:

fan of convection bake oven 91199002990 Kenmore 30

A:

Thank You for choosing Sears PartsDirect.com and being a valued member. It is unfortunate to hear that you are having issues with your oven and I do understand your frustration. Glad to help out. I'm looking at your model number and from your description I suspect that fan motor is failing. Here is a link that will help troubleshoot the issue. You will want to verify that you are getting power to the fan. If you are not getting power then you may have an issue with the controller. I have included a link to our PartsDirect page where you can purchase the part you need to complete your repair. Just click the blue link above to be taken to the page. I trust this information will help you.

 

Thank you for choosing Sears PartsDirect.com.

Read More
Sherman_G_Wallace -
Sears Technician
September 26, 2014
Q:

Error code F-0

A:

A non working Oven is not something any of us want to see. If you are technically handy, this is a good site to get instruction and fix some things yourself. If you do not feel confident doing your own repairs, an option is to visit Sears Home Services and use the scheduler. While you wait for the expert to review your model, you can check the bottom links for some possibilities. Hope this is of help.

Read More
Priscilla V -
April 10, 2011
A:

Thank you for your question and I understand your concern.

The "F0" fault code implies the Clear/OFF pad is shorted or a touch pad failure. If the code cannot be cancelled, unplug or disconnect the power supply from the range and then disconnect the keypad and then power it up. If "F0" ceases, replace the keypad/glass assembly; if "F0" is still present, replace the main oven control.

I added an image below with instructions how to access the control and glass panel. NOTE: Disconnect the range from the power supply before servicing.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
April 12, 2011
See more answers
Q:

Kenmore Elite electric range Model 911.99002990 with F4 code and beeping. What does it mean?

A:

Diagnosing all the error codes that the modern appliance displays can be confusing. I found a similar question from a previous expert post that may answer your question. If you decide you prefer to have an experienced technician make repairs and do the further testing, an option is to visit Sears Home Services and use the handy scheduler. I attached the links below. Hope this helps!

Read More
Barbara H. -
November 18, 2010
A:

The first link that Barbara H. provided in the above response correctly identifies the F4 as indicating that you have a problem with the oven temperature sensor probe. The first image below shows how to access this component. Unplug the range to disconnect electrical power before accessing internal components.

If you have a volt/ohm meter, you can check the resistance of the oven temperature sensor probe. It should measure around 1100 ohms at room temperature. If it measures less than 950 ohms, then this is the failed component that is causing your F4 code.

You can order the sensor from the Sears PartsDirect website. The part number is WB23T10002. Here is a direct link to that part: Sensor . This part costs around $40.

If the resistance of the sensor is okay, then you could have a wiring failure or a bad electronic oven control board. You can plug the sensor back in and check the entire sensor circuit from its connection to the electronic oven control board in the console (with the range still unplugged ). The second image below shows the wiring diagram for this range with the sensor circuit circled in red. To access the control board, unplug the range and remove the back panel behind the console. Unplug the connector for the sensor circuit from the control board and measure the resistance through that circuit using a volt/ohm meter. If the resistance is the different than what you measured directly at the sensor probe, then you apparently have a problem with the wiring harness between the control board and the sensor.

If the resistance through the wires that connect to the control board is the same as the measurement at the sensor (around 1100 ohms), then a bad control board is likely causing this problem.

An intermittent problem may be difficult to diagnose.

If you need more help, reply with additional details and we will assist you further.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services . A repair visit will likely cost around $130 for labor. The parts would likely cost between $40 and $150.

Read More
Lyle W -
Sears Technician
November 19, 2010
See more answers

Top Parts