Model #91195875891 KENMORE Free Standing, Electric

  • Backguard
    3 Results
  • Maintop
    3 Results
  • Body
    3 Results
  • Door
    3 Results
  • Door Lock
    3 Results
  • Wiring Components
    3 Results
Find part by diagram >

Question and Answers

Q:

need wiring diagram for wb30t10047 91195575891 Kenmore Range

A:

Thank you for choosing SearsPartsDirect.com and for contacting us with your question about your Kenmore range model 911.95875891. I am so sorry the element needs to be replaced. I understand your concern about the new part not connecting the same as the original.  I will be happy to help you with this. 

SAFETY WARNING: Disconnect the power supply before beginning your project to prevent the risk of electrical shock which can result in property damage, serious personal injury or even death. Internal parts may have sharp edges. Use caution and wear work gloves to prevent serious cuts. If you are not comfortable completing this repair, you can set up service at www.SearsHomeServices.com or by calling 1-800-469-4663 (1-800-4MY-HOME).

I was unable to locate a clear image of the wiring diagram, however, I have included information that the technicians would use when installing the replacement element. The replacement part has an internal jumper wire so the jumper wire that was on the original part is no longer used. The element can be difficult to replace and connect properly. If you are not positive you can complete this repair correctly I recommend you have a technician complete the repair for you.  

I hope this answers your question. Thank you for choosing Sears, we appreciate your business. 


Read More
Rachel Morgan -
Sears Technician
August 11, 2015
Q:

Oven takes long time to preheat 91195875891 Kenmore 30" free standing range

A:

Hello glad to help.  Thank You for choosing Sears PartsDirect.com
 
I am sorry and do understand your frustration when there is trouble with the range.
 
Glad to help out.   Im  looking at your Kenmore model number 911.95875891.
 
Everything in the oven is lighting and working but you just aren't getting the right settings that you desire.   I see you tried what I would suggest and that is put an oven safe thermometer in the oven and set the oven to 375 and see if it matches the thermometer you set in the oven.   It doesn't so you need to change out your oven sensor.  It took the place of an oven thermostat.   I have it on the link below. 
 
 
 
 If you have further questions please let me know.
Thanks for choosing Sears PartsDirect.com
 

Read More
Larry L -
Sears Technician
October 31, 2013
A:

No, I think you misunderstood part of what I said. The oven DOES reach 375 if I set it to 375 (or whatever I set it to), and once it reaches the correct temperature it does maintain that temperature. To me, that means that the Oven Sensor is probably working right. What it does not do is preheat fast, when I turn the oven on it takes 20-30 minutes to get to whatever temperature I have set it to. AND additionally, the beep that happens when preheat is supposed to be done, it does beep about 5 minutes after turning the oven on. But the oven has not reached the right temperature at that short amount of 'preheat' time. I hope I have explained more clearly. What part do you think I need to replace?

Read More
Elizabeth -
October 31, 2013
A:

Hello glad to help.  Thank You for choosing Sears PartsDirect.com

Sorry for the trouble still.

I still think it would be the sensor for the oven.   Do you broil and bake?   Check both and see if they are both working well.  

Providing that you  have done that then the next issue would be with the control board.  All wiring and heating determinations comes through the control board.   I would take out the sensor, the bake element, the broil element and take an ohm meter to them and also to the wires that they connect too, to see which one is bad.

 

Read More
Larry L -
Sears Technician
November 04, 2013
See more answers
Q:

Element for Kenmore Glass Top Range, 911.95875891

A:

I found some information for you that I am hoping will help you install the element. Please click here: Installing Replacement Element. Your expert will also help answer your question. It may take two business days. I do hope that everything works out.

Read More
Marc -
March 12, 2013
A:

Hello Robert. That link for a previous answer that Marc posted in the above response covers the same issue on a similar range. I posted the wiring diagram for your Kenmore Range Model 911.95875891 in the first image below.  That diagram is blurry but it is the best reproduction that I have for that document. That may help you see the wire colors for the connections on that element. The second image shows more information on connecting that revised part. The original part is no longer available from the manufacturer. The replacement part has an internal jumper wire so that the jumper wire that was on the original element is no longer used. That information may help you connect the new part. Be sure that you unplug the range before accessing and replacing internal components.

 

If you need more help, reply with additional details and we will assist you further.

 

The element can be difficult to replace and wire up properly. The wiring on the element must be competed accurately. If you are not positively sure that you can wire that element correctly, then I recommend that you have a service technician install that element. You can schedule service through this link: Sears Home Services Range Repair. 

Read More
Lyle W -
Sears Technician
March 13, 2013
A:

Lyle W, I haven't disconnected the old element. If I number the wires 1, 2, 3, and 4 on the old element per your original/replacement diagram and replace them at the 1, 2, 3, 4 positions on the new element (discarding the jumper), this will give me the correct wiring for the new WB30T10047 element. As a retired engineer, this seems to be a reasonably simple task. Am I missing anything? Robert

Read More
Robert -
March 13, 2013
A:

Hello Robert. I am glad to hear that you did not disconnect the wires from the old element yet. Yes, your strategy for connecting the new element is sound. Transferring the wires directly from the old element to the new element in the manner that you described should resolve your problem. If you need more assistance, let us know.

Read More
Lyle W -
Sears Technician
March 14, 2013
A:

Lyle, after reviewing the (original part/replacement part diagram) and the (H1/H2 switch picture) that you posted, I have a question. If you replace the wires 1, 2, 3, 4, per the diagram, the 1A and 2A connections on the original become reversed per the picture showing H1 to 2A and H2 to 1A. Is that correct, or should the connection revert back to matching numbers on the back of the old/new switches, 1A to 1A and 2A to 2A? I hope this reply is not too confusing. Robert

Read More
Robert -
March 14, 2013
A:

Lyle, I am waiting on a reply to the above question before connecting the new element. Can I damage the element if the H1 and H2 wires are reversed? Hope to get a reply soon. Robert

Read More
Robert -
March 18, 2013
A:

Hello Robert. I apologize that I did not reply to that earlier request. You can damage the wiring and components in that range if the element is wired incorrectly. To make sure that you get it wired correctly, I recommend that you send us a digital picture of the current element with the wires attached. Also send us a picture of the new element with the markings on the spades shown. That will help us advise you accurately on this repair so that we can make sure that you get those wires connected properly. (There is a 2MB limit for digital pictures that can be attached to replies.) Once we receive the pictures, we should be able to help you further.

Read More
Lyle W -
Sears Technician
March 19, 2013
A:

Lyle, thanks for your help. I don't have the ability to send pictures, so I just marked the old element wires carefully and connected them to the same markings on the new element, 1A to 1A, 2A to 2A, etc. per the switch picture you posted. The element seems to work fine. The large diagram showing original/replacement part wiring (1, 2, 3, 4) is therefore incorrect. Robert

Read More
Robert -
March 19, 2013
A:

Thanks for letting us know how you wired that switch Robert. We are glad to hear that it is working properly. Let us know if you ever need more assistance.

Read More
Lyle W -
Sears Technician
March 20, 2013
See more answers

Top Parts