Model #9119584591 KENMORE Free Standing, Electric

  • Backguard
    3 Results
  • Door Lock
    3 Results
  • Main Top
    3 Results
  • Body
    3 Results
  • Wire Harness
    3 Results
  • Door
    3 Results
Find part by diagram >

Question and Answers

Q:

What do the F2 and F3 codes mean for a Kenmore range?

A:

Both the F2 and F3 codes could be the oven sensor, EOC (Electronic Oven Control), or the wiring between the two.

I have included the entire tech sheet for this model (see images below). It explains the error codes and the tests needed for more complete diagnosis. It also has a section on disassembly that you may use to access the oven sensor and EOC. Follow the tech sheet directions and it should help with the repair of your oven. If you require further assistance please resubmit question with details of the checks you have made. I will be looking forward to helping you again in the near future.

Read More
Landell -
Sears Technician
January 26, 2010
A:

I have a GE model JMP31WOA2WW drop in range and simply can't find the termal switch, in door lock circuit, that tech sheet referinces to. Can you help or do I have to keep looking?

Read More
Rick -
October 15, 2012
A:

LANDELL PLEASE SEND ME THE ENTIRE TECH SHEET FOR THIS MODEL AS WELL. I NEED EXACTLY WHAT YOUSENT FOR THEABOVE EROR CODE (F2). HOW DO I GET TO TE EOC (Electronic Oven Contrl).

Read More
SURRY FRY -
September 02, 2013
A:

Please do the following for me as well, .... I have included the entire tech sheet for this model (see images below). It explains the error codes and the tests needed for more complete diagnosis. It also has a section on disassembly that you may use to access the oven sensor and EOC. Follow the tech sheet directions and it should help with the repair of your oven. If you require further assistance please resubmit question with details of the checks you have made. I will be looking forward to helping you again in the near future.

Read More
SURRY FRY -
September 02, 2013
A:

Im also having problems with my oven throwing me F2 and F3 codes...I would also like the tech sheet for the Model#911.9584591....thanks!!

Read More
Amanda -
September 04, 2013
See more answers
Q:

"Surface Unit" light

A:

It can be very frustrating when the surface light on your stove malfunctions and stays on. I did some research and provided a link to a similar question and answer on our site. I hope this will shed a little more light on the issue until the Expert responds to your question in more detail within 24 to 48 hours.

Read More
Julio -
December 01, 2012
A:

Thank you for your question and I understand your concern.

Each one of the radiant surface elements has it's own thermal switch which will cause the hot surface indicator to come once the burner gets hot. One of the 4 radiant burners is faulty and it will need to be replaced. In order to know which model number you have; you will have to locate the model and serial number tag on the range. The model number could be on the oven frame below or to the side of the oven cavity opening. You will need to open the oven door to locate it. It could also be located on the oven frame behind the storage drawer.

I strongly suggest calling a service technician to diagnose which radiant burner will need to be replaced. It will require taking the top off and using a volt/Ohm meter to test the bi-metal switch on each radiant burner.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
December 03, 2012
See more answers
Q:

Kenmore Electric Range 911.9584591

A:

The holdays are here and having our oven working is a must. I'm sorry to hear that you are having some difficulties with your Kenmore Electric Range. I did some research for you at Managemylife and found an expert answer to a similar question that may help until your expert can respond to your specific question. The link is attached below. If you do decide to schedule service and have a qualified technician help you, I have also attached a link to Searshomeservices. I hope these links provided assist you.

Read More
James -
November 25, 2011
A:

I checked the technical information for that range. The bake element is the only one used for the preheat cycle in the bake mode. There is a possibility that you have a bad bake element that is causing this problem. A bad clock control board could also prevent that bake element from heating. You could also have a wiring failure that would cause this failure.

I recommend that you unplug the range and check that bake element first. If you see no visible damage, you can test that element with a volt/ohm meter as shown in this brief repair video: Bake Broil Heating Element Testing . Here is a video that shows how to access that bake element: Bake Element Removal . You should measure about 22 ohms of resistance through that bake element. If that bake element is bad, it will need to be replaced. You can order that bake element from the Sears PartsDirect website. The part number for that bake element is WB44K5012. Here is a direct link for that part: Bake Element .

If that bake element is okay, then you can check the wiring connections on that clock control board (with the range still unplugged ). You should be able to use the procedure shown in the first image below to access that clock control board in the console. The second image shows a wiring diagram for that range with the bake circuit traced in the wire colors that it uses for that bake circuit. You can check the connection of that yellow wire on the control board. The orange wire must be connected properly since the broil element works properly. You can measure the resistance through that bake circuit from the control board (with that bake element re-installed properly). You should measure the same 22 ohms that you measured at the element if the wiring in that circuit is okay. If the element and wiring are both okay, then that control board would apparently need to be replaced. The part number for that clock control board is WB27K5194. I checked on the availability of that part. I do not see that part available through Sears PartsDirect or other part suppliers. If the clock control board is bad, you may need to replace the entire range to fix this problem.

If you need more help, reply with additional details and we will try to assist you further.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services . NOTE: Keep in mind that if the technician determines that the failure is caused by that control board and it is not available as a repair part, then you would wind up having to pay for the labor of a service call even though the range cannot be fixed.

Read More
Lyle W -
Sears Technician
November 28, 2011
See more answers

Top Parts