Model #91195475891 KENMORE Free Standing, Electric

  • Backguard Section
    3 Results
  • Maintop Section
    3 Results
  • Body Section
    3 Results
  • Wire Harness And Wiring
    3 Results
  • Door Section
    3 Results
  • Door Lock Setion
    3 Results
Find part by diagram >

Question and Answers

Q:

How do I replace the broiler element in my Kenmore electric self-cleaning range?

A:

The part number that you submitted in the details of your question (5303501140) does not appear to be valid. The model number (790) is just the first 3 digits of a longer full model number. Since the broiler element in most Kenmore electric range models beginning with 790 will be virtually the same, you should be able to use these directions to change the element:

  1. Unplug the range (or shut off the breaker) to completely disconnect electrical power. This step is very important when changing a broil element.
  2. Remove the screws that secure the broiler element to the back wall of the oven.
  3. Remove the screws that secure the supports on the roof of the oven cavity. Support the element so that it does not fall down when removing this support.
  4. Carefully pull the broiler element forward to that the electrical power leads come out of the back wall of the oven. You should see wires connected with spades on the back of the element.
  5. Remove the wires from the element.
  6. Connect the wires to the new element and carefully push the new broiler element ends into the back wall of the oven.
  7. Replace the screws in the top support of the broiler element on the roof of the oven cavity.
  8. Replace the screws that secure the broiler element in the back wall of the oven.
Reconnect electrical power and test the broiler element to see if it is working properly.

If you need more help, resubmit your question with the full model number of your Kenmore range (and the part number of the broiler after rechecking it).

Read More
Lyle W -
Sears Technician
March 02, 2009
A:

you explained everything except-how do the wires come apart?

Read More
Joanne -
July 25, 2011
A:

does anyone have an answer tothat?

Read More
Joanne -
July 25, 2011
A:

how do I change the broiler element on my kenmore electric range model #911.95475891

Read More
Mike -
January 31, 2013
See more answers
Q:

can i replace the bake element on my kenmore range model 119.95475891 by myself?

A:

First, the model number you submitted is incorrect. I must assume the correct model number is 911.95475891. Removing and replacing the bake element is not a difficult procedure.

  1. Disconnect the power supply from range by unplugging the power cord from the power source or by flipping both house circuit breakers dedicated for the range inside the house circuit breaker box.
  2. Remove the oven racks.
  3. Remove the screws securing the bake element to the rear panel.
  4. Slide the bake element outward slowly until you have room to disconnect the wires connected to the bake element. Note: Do not allow the wires to recoil back through the openings after disconnecting them from the element or you will have to slide the range out and remove the rear panel in order to push the wires back through the openings.
  5. Reverse the procedure to install the new bake element. The bake element is part #WB44K5012 which is available for ordering at Sears Parts Direct .

Read More
Joey S -
Sears Technician
May 10, 2010
Q:

Why is my Kenmore oven not turning off?

A:

On something like this it sounds like a relay is stuck on the control board. Unplug the unit from the wall or disconnect power for 30-40 seconds. If the oven still heats after restoring power, the control board will need to be replaced. If not, the touchpad may need replaced.

Read More
biker dave -
Sears Technician
September 11, 2008

Top Parts