Model #9119544990 KENMORE Free Standing, Electric

  • Backguard Section
    3 Results
  • Main Top Section
    3 Results
  • Wire Harness
    3 Results
  • Body Section
    3 Results
  • Oven Door Section
    3 Results
  • Door Lock Section
    3 Results
Find part by diagram >

Question and Answers

Q:

circuit board for oven burned out. 9119544990 Kenmore 30" radiant free standing range

A:

Hello glad to help.  Thank You for choosing Sears PartsDirect.com

I am sorry and do understand your frustration when there is trouble with the range.

Glad to help out.   Im  looking at your model number 919.9544990.

I see your circuit board has burned out.  I hate to be a bearer of bad news but through us at Sears Parts Direce we no longer have a new board in stock at any part store or any factory.   The part number for the key board  you need is WB27K5127.   You can take that part number and use your search engines of the computer.   Someplace may have one in their inventory, just that we do notl.

 If you have further questions please let me know.

Thanks for choosing Sears PartsDirect.com

Read More
Larry L -
Sears Technician
September 18, 2013
Q:

kenmore range model #911.9544990

A:

I know how important it is to have the correct parts for your range and I am sorry for the inconvenience. I did some research and I was able to find two links in where you can find replacement parts. I hope this helps with your range troubles while you wait for your expert response.

Read More
Joseph P. -
August 06, 2012
A:

I see that the oven body is no longer available through the Sears parts source. I checked for an equivalent part but I did not find one. I checked some other part sources and could not find a replacement part. I performed a web search for a used part but I did not find one available.

In this situation, I recommend that you consider replacing the range unless you can find that part through a web search or at a local parts supplier.

Read More
Lyle W -
Sears Technician
August 07, 2012
See more answers
Q:

MY OVEN OR BROILER WONT WORK. ON & preheat lights flashing kenmore model #911.9544990

A:

When an appliance goes out we usually see money going out the window, either in repair cost, or replacement. Managemylife.com can take the mystery out of the repair and an expert can tell you if its time for a replacement if you ask him. I did some research for you at this web page and found an expert answer to a similar question which may shed some light on the problem. If you want to schedule service, and have a qualified technician to assist you, I have attached the link to searshomeservices.com. I hope this information will be useful until your expert can

Read More
James -
February 18, 2011
A:

The preheat lights flashing normally indicates that the oven temperature sensor probe is "open" or "shorted".

I recommend that you unplug the range and access the sensor probe as shown in the first image below. Check the resistance of the sensor probe using a volt/ohm meter. It should measure around 15 ohms of resistance at room temperature. If it is "open" (measures Ol -- open load or infinite resistance) or "short" (measures near zero ohms) then the sensor probe (part WB21X158) will need to be replaced.

You can order parts from the Sears PartsDirect website.

If the resistance of the sensor is okay, you could have a wiring failure or a bad electronic control board. I provided technical information about this failure in the second image. Plug the sensor back in and check the resistance of the circuit from the control board (with the range still unplugged). The second image shows how to open the console. If the resistance at the control board is different than the resistance measured directly at the sensor, then you have a problem with the wiring harness (usually in the disconnect plug). If the resistance through the sensor circuit is normal at the control board (around 15 ohms), then you will probably need to replace that control board in the console.

These tips should help you resolve this problem in your range. If you need more assistance, reply with additional details and we will help you further.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Lyle W -
Sears Technician
February 18, 2011
See more answers

Top Parts