Model #9119398890 KENMORE Ranges, Electric

  • Backguard Section
    3 Results
  • Main Top Section
    3 Results
  • Body Section
    3 Results
  • Door Lock Section
    3 Results
  • Oven Door Section
    3 Results
  • Wire Harnesses And Components
    3 Results
Find part by diagram >

Question and Answers

Q:

f 1 error code on kenmore range

A:

Having a properly working range is very important. The error codes can be frustrating sometimes. I found some information for you that I am hoping will help you with the range. I am adding the link below to help you with your question while you wait for your expert response. I do hope that this will help you with the range.

Read More
Marc -
September 24, 2012
A:

Thank you for choosing Manage My Life.com, I do understand your concern in having a properly working range in your home. The F1 error code indicates a failed transistor in the ERC, Electronic Range Control. If disconnecting the power to the unit, by unplugging does not reset the range the ERC will need to be replaced. The ERC can be looked up and ordered from Sears Parts Direct . If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Maira -
Sears Technician
September 25, 2012
See more answers
Q:

Error code reading on Kenmore Electric Range

A:

Not having a properly working range can be very frustrating. Looking in manage my life.com I came upon some information that can be of help to you. I have attache the link below.Hope it helps!

Read More
Maira -
March 01, 2012
A:

Unplug the range for 5 minutes and then plug it back in. That will sometimes clear that code if it was caused by a power surge or glitch through the electrical lines. If it returns, then you can use the information shown below to resolve this problem.

That F5 code indicates that you have a failed clock control board in the console of the range. You would need to replace that part to fix this problem. That part is expensive. It costs almost $400. The part number for that clock control is WB27M4. Here is a direct link for that part: Electronic Range Control Clock . Based on the cost of that part, you may consider replacing the entire range instead of replacing that clock control board.

If you want to proceed with the repair, you can order that part through the link that I provided above. Unplug the range to disconnect electrical power before accessing and replacing internal components. The image below shows how to open that console to access that clock control board for replacement. This information should help you complete the repair if you decide to go that route.

If you get to the point where you need to have a service technician complete this repair, you can schedule service through this link: Sears Home Services .

If you decide to replace the range, you can view current models on the Sears.com website.

If you need more help, let us know.

Read More
Lyle W -
Sears Technician
March 01, 2012
See more answers
Q:

Kenmore limited edition stove/oven model #: 911.9398890 serial #: 8364646

A:

Error codes are like a mystery it can be hard to find out why they are popping up. I have searched in the Manage My Life website and found some great links. You can also get service with a Sears technician. I have attached the links below. Have a nice day!

Read More
Dezeray S -
September 26, 2011
A:

Thank you for your question on the F3 error code on your range.

This error code is related to the sensor circuit in the oven.

This sensor is what controls the oven temperature and it has failed.

Because this part does not seem to be available any I would suggest that you have a technician check out the range and see if he has a substitute sensor that will work.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Please let me know what happens with the repair.

Sam A.

Read More
Sam A -
Sears Technician
September 27, 2011
See more answers