Model #91193575790 KENMORE Free Standing, Electric

  • Backguard
    3 Results
  • Maintop
    3 Results
  • Body
    3 Results
  • Wire Harnesses And Components
    3 Results
  • Door
    3 Results
  • Door Lock
    3 Results
Find part by diagram >

Question and Answers

Q:

Was there a recall on the oven/clock control board and if so is it still covered under the recall? 91193575790 Kenmore 30" electric free standing range

A:

Thank you for choosing SearsPartsDirect.com. I am sorry to hear about your mother's control board going bad! I know how frustrating this must be. I did take a look and there is not a recall on the range. Also, that control board is no longer available. You can try an aftermarket search such as Ebay or Amazon. However, I cannot guarantee the results.  I hope this helps. Good luck getting that range going! Have a great day!

Read More
Samantha A -
Sears Technician
November 08, 2013
Q:

Front right burner goes to high no matter setting 91193575790 Kenmore 30" electric free standing range

A:

Hello glad to help.  Thank You for choosing Sears PartsDirect.com

I am sorry and do understand your frustration when you are having trouble with your range.

Glad to help out.   Im  looking at your model number 911.3575790 

What is wise to do when you are having this problem is to change the infinite switch and the terminal block.   You asked for the element so will give all that too you on the links below.  

Infinite switch per model 911.93575790

terminal block per model 911.93575790

large burner per model 911.93575790

If you have further questions please let me know.
Thanks for choosing Sears PartsDirect.com

Read More
Larry L -
Sears Technician
August 13, 2013
A:

Thank you Larry! I shall get these on order...

Read More
Randy -
August 13, 2013
See more answers
Q:

Need fault isolate an oven that won't come to temp. - Model 911.93575 891

A:

We rely on our appliances for every day use. So it can be difficult to adjust without them. Upon researching your question I have attached some links below that may help you out. I hope these links are useful!

Read More
Jackie S -
May 22, 2011
A:

This doesn't help, your replies are for a gas grill or stove, by the Model # I would have expected an answer for an electric oven. Please try again!

Read More
Todd -
May 22, 2011
A:

The images below show the technical information on your electric range. You could have a problem with the electronic control board, the temperature sensor or an element.

Check broil element to make sure that it is heating properly in the broil mode. The first image shows that the broil element is used exclusively in that broil mode. If the broil element is not heating, you can unplug the range and check the resistance of that element using the information shown below. The broil element should measure around 17 ohms of resistance. Here is a short video that shows how to check the heating elements: Bake Broil Heating Element Part Testing . You don't have to remove the element to test it. You can remove one wire and then check the resistance. If the broil element is bad, it will need to be replaced.

If the broil element is heating properly in the broil mode, you can check the resistance of the bake element using the procedure shown above.

The temperature sensor will need to be checked for resistance to determine if it is okay. Here is a link for a short video that shows how to check that component: Oven Sensor Testing . Unplug the range before accessing internal components. You should be able to access the sensor probe to test it by using the procedure shown in the third image. It should measure around 1100 ohms at room temperature. If it does then that component is okay.

If the elements and the sensor are all okay, your likely failure is that electronic clock control board in the console (part WB27T10079R). You can access that component by unplugging the range and removing the screws on the bottom corner of each side of the console. You should then be able to lift the back top part of the console to release it. Fold the console forward and lay it on the top of the cook top. Check the wiring on the control board before replacing that component. If the wiring is okay, you can probably fix this range failure by replacing that control board.

You can order parts from the Sears PartsDirect website.

The clicking that you are describing in the bake mode may be normal. As shown below, the elements will cycle in that mode but not in the broil mode.

I hope that this information helps. I apologize for the initial information that received on the gas ranges. We try to provide an initial response that may help you. That initial response is then followed by an advanced technical reply from an expert in that category. If you need more help, reply with additional details and we will assist you further.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

NOTE: The model number that this answer is based on is 911.93575790. The difference in those last 3 numbers (color and revision) should not affect this answer. You should be able to access a parts diagram using that 911.93575790 model number if necessary.

Read More
Lyle W -
Sears Technician
May 23, 2011
See more answers

Top Parts