Model #9119352192 KENMORE Free Standing, Electric

  • Backguard Section
    3 Results
  • Door Lock Section
    3 Results
  • Main Top Section
    3 Results
  • Oven Door Section
    3 Results
  • Body Section
    3 Results
  • Wire Harnesses And Components
    3 Results
Find part by diagram >

Question and Answers

Q:

Have Kenmore range/oven 9119352192 with error code of F4. I spoke to parts and ordered a sensor, replaced today and still the F4 error. Now what?

A:

With the error on your range can be rather upsetting especially with Thanksgiving approaching. I have done some research on the Manage My life website and have located a link similar to your issue. While you are waiting for a detailed reply from an expert I have provided the link below. Hope this helps!

Read More
Priscilla V -
November 21, 2012
A:

I saw this conversation, but there is a F4 error but not listed on the error list that I have seen. The techs that I spoke with say there is the temp sensor or a control panel issue, so I posted my issue to see what the expert online tech has to say. Thanks for your help tho.....I appreciate it! Great timing tho with T-day tomorrow.....

Read More
Laura O'Brien -
November 21, 2012
A:

Thank you for your question and I understand your concern.

Check the oven temperature sensor circuit for a short. If the sensor circuit and new sensor is not shorted, the electronic oven control/clock assembly is most likely faulty.

Measure the Sensor circuit resistance at the sensor/lock switch connector at the oven control with Sensor connector unplugged. It (should read approx. 1100 Ohms at room temperature) across pins 4 and 5. Measure lead to lead and each lead to chassis ground.

If the sensor measure approximately 1100 Ohms at the control board/clock assembly; the electronic oven control/clock assembly is likely faulty.

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Read More
Joey S -
Sears Technician
November 23, 2012
A:

I too have a similar issue. It began w/ f4 then we turned off then on at fuse box that worked then it stopped after a few months and this time it said FOOD where the time is... we just unplugged it & now the time pops up but not able to correct the time ands my oven is STILL NOT WORKING! IDK WHAT TO DO SINCE I'M TOO BROKE FOR SERVICE MAN PLUS,this is an older model... PLEASE HELP ME! THANKS KRISSY

Read More
krissy -
August 03, 2015
A:

I too have a similar issue. It began w/ f4 then we turned off then on at fuse box that worked then it stopped after a few months and this time it said FOOD where the time is... we just unplugged it & now the time pops up but not able to correct the time ands my oven is STILL NOT WORKING! IDK WHAT TO DO SINCE I'M TOO BROKE FOR SERVICE MAN PLUS,this is an older model... PLEASE HELP ME! THANKS KRISSY

Read More
krissy -
August 03, 2015
See more answers
Q:

We receive an "F-2" error message when trying to use the broiler. We receive an "F-1" error message when trying to bake at temoeratures above 400. 9119352192 Kenmore Elec free ...

A:

Thank you for choosing SearsPartsDirect.com and being a valued member.  I can certainly understand how frustrating it can be when your range displays an error code. 

 The F2 error code means oven over temperature. 

OVEN OVER TEMP.
• Door unlocked - sensor exceeded
650°F. (2237 Ohms)
• Door locked - oven exceeded 902°F. (2700 Ohms)
REMEMBER: ERC measures resistance of sensor circuit, not
actual oven temperature.
DURING CLEAN
• Lock switch opened and sensor in
excess of 650°F.

If actual over temperature condition
occurred:
• Look for welded relay contacts. If no over temperature condition occurred:
• Look for a high resistance connection or any other cause of high resistance in the sensor
circuit. (Intermittent Sensor or Sensor Circuit)

This requires a service technician to diagnose. 

You can also visit searpartsdirect.com for parts, diagrams, and repair information.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for your question. Have a great day. 

Read More
Natasha12 -
Sears Technician
November 07, 2014
Q:

I have a kenmore stove and just replaced the oven units and temp sensor and I am still getting an F4 code read out when I try to turn on the oven.

A:

It always a little frustrating to have one of our appliances start to have issue. I'm sorry to hear that you are having some problems with your Kenmore stove. I did a little research for you at Managemylife and found an expert answer to a similar question that may help until your expert can respond to your specific question. The link is attached below so you can check it out. If you do decide to schedule service and have a qualified technician help you, I have also attached a link to Searshomeservices. I hope the links help out.

Read More
James -
February 22, 2012
A:

I have replaced the heating elements and the sensor and it still says f4. Is there something I have to reset?

Read More
vicki -
February 23, 2012
A:

That F4 code indicates that the clock control board detects a problem with the oven temperature sensor circuit in most ranges. Without a model number, it is impossible to tell for sure if that is what your control is indicating in this range. If you reply with that model number, then we can check that fault code and provide specific troubleshooting and repair advice.

If you want to proceed with some additional checks while you wait for a response after replying with that model number, I recommend that you check the resistance through that oven temperature sensor circuit from the wiring connections on the clock control board in the console. Here is a link for a video that shows how to check an oven temperature sensor probe using a volt/ohm meter: Oven Sensor Testing . You can test that circuit by unplugging the range and access the clock control board in the console. The sensor circuit is often connected to the control board through violet (purple) or white wires. Unplug the connection from the clock control board and measure the resistance through that sensor circuit. It should measure around 1100 ohms in most ranges. The resistance through that circuit should be the same as the resistance measured directly at the sensor probe. If not, then a wiring harness failure is probably causing that F4 code. The most vulnerable part of that harness is the disconnect plug at the sensor. You may need to cut off that disconnect plug and properly connect those wires using ceramic wire nuts. This may fix your problem.

If that resistance through the sensor circuit is okay as measured from the clock control board, then that clock control board may need to be replaced.

Reply with additional details (and that model number) if you need more help.

You can order parts from the Sears PartsDirect website. Be sure that you unplug the range before accessing and replacing internal components.

If you get to the point where you need to have a service technician repair the range, you can schedule service through this link: Sears Home Services .

Read More
Lyle W -
Sears Technician
February 23, 2012
A:

Thank you for your response, the model number on my kenmore stove is 911.9352192. My stove is hardwired so we can't unplug it, but we will check the sensor connection in the clock panel and see how that works. Thank you again.

Read More
vicki -
February 23, 2012
A:

Hello Vicki. Thanks for providing that model number. That F4 does indicated that the control detects a shorted (resistance would measure near zero ohms) sensor. The normal resistance of the sensor in that range should measure around 1100 ohms at room temperature. Let us know if you need more help.

Read More
Lyle W -
Sears Technician
February 23, 2012
A:

We have looked everywhere for ceramic wire nuts, no one has ever heard of them so we are going to use the regular ones

Read More
vicki -
February 27, 2012
A:

The ceramic wire nuts are designed to withstand higher temperatures since they will be used on the back of the range. As long as the wire nuts that you are using are rated to withstand high temperature (up to about 300 degrees F), they should be okay. That area of the range should not normally get that hot but the use of high temperature rated wire connectors is recommended.

Read More
Lyle W -
Sears Technician
February 27, 2012
A:

Thank you very much. I will check the recommendation on the package and see what happens. Keep your fingers crossed that I no longer get an F4 code. Thanks again.

Read More
vicki -
February 27, 2012
A:

Those electrical components are sometimes rated in Centrigrade instead of Fahrenheit. If the rating has a C behind the temperature then you can use wire nuts rated for 150 C or 200 C.

Read More
Lyle W -
Sears Technician
February 27, 2012
See more answers

Top Parts