Model #91193268690 KENMORE Free Standing, Electric

  • Backguard Section
    3 Results
  • Door Lock Section
    3 Results
  • Body Section
    3 Results
  • Door Section
    3 Results
Find part by diagram >

Question and Answers

Q:

Kenmore electric range 911.93268690 displays an error code F2 when the oven is turned on?

A:

Managemylife.com is always a great resource to find the answers to just about anything. Your expert will research your question and respond within two business days but usually sooner.

Read More
Alina F. -
January 05, 2012
A:

The F2 error code is indicating a high resistance of the oven sensor probe. It could also be a bad oven sensor or loose oven sensor circuit. It could also be a failed control board too.

If an actual over temperature condition occurred then the control board will need to be checked for welded contacts on the relay. If the relay contacts are stuck/welded, replace the oven control board.

If no over temperature condition occurred then the oven temperature sensor probe will need to disconnected and tested with an OHM meter. I do recommend having a technician thoroughly examine and repair your range. If you would like to schedule an appointment, you may do so by logging onto www.SearsHomeServices.com . If you have any other questions, please feel free to reply back to this thread. Thank you for contacting Manage My Life.

Read More
Tammy S -
Sears Technician
January 08, 2012
See more answers
Q:

I have an F3 error code on my Kenmore 911.93268690 oven

A:

It can be real frustrating when an appliance is not working correctly. I did some research at managemylife.com and found an expert answer that may shed some light on the ovens problem. I have attached the link below. I hope this helps until your expert can respond to your question.

Read More
James -
December 08, 2010
A:

I know it's frustrating when the oven stops working. The "F3" fault code is indicating an oven temperature sensor failure or a temperature sensor circuit failure. The oven temperature sensor could be open or shorted. Test the sensor for proper ohm value, frayed or pinch wiring, or connector damage. The oven temperature sensor probe can be found sticking out from the rear wall inside the oven cavity. It will need to be disconnected and tested with an ohm meter. Be sure to disconnect power to the range first. I added a chart in the image below of the resistances of the oven sensor at specific temperatures. At normal ambient room temperature, the oven temperature sensor should have a resistance value of 1050-1100 ohms. If the resistance is more than 5% off, the sensor # WB21X5301 will need to be replaced. I hope this will help you.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Scott D -
Sears Technician
December 09, 2010
See more answers
Q:

Error Code F2

A:

I can understand how it can be frustrating when one of your major appliances is not working correctly. I was able to attach a few things for you, the first attachment is the Owner's Manual it always comes in handy when you are needing specific information upon your oven. The second is a similar question was asked and an expert answer with some helpful information, i hope that this is helpful.

Read More
celene -
December 05, 2010
A:

Thank you for your question and I understand your concern with your range displaying "F2". The fault code is meaning the oven exceeded 624 degrees with the door unlocked or it exceeded 925 degrees with the door locked.

If an actual over temperature condition occurred then the control board will need to be checked for welded contacts on the relay. If the relay contacts are stuck/welded, replace the oven control board.

If no over temperature condition occurred then the oven temperature sensor probe will need to disconnected and tested with an OHM meter. The oven temperature sensor probe is located inside the oven protruding from the upper right or upper left hand corner. If you see the two screws securing the sensor then it can be removed from inside the oven cavity. If you do not see any screws then the sensor must be removed from the rear of the oven.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

The oven temperature sensor should have a resistance measurement of approximately 1100 ohms at room temperature. See image below. NOTE: Disconnect the power cord from the range before removing the rear panel.

The oven temperature sensor is part #WB21X5301 and can be ordered from Sears Parts Direct .

Read More
Joey S -
Sears Technician
December 07, 2010
See more answers

Top Parts

Recommended maintenance parts & accessories