Model #9117398710 KENMORE Range (gas)

  • Backguard Section
    3 Results
  • Main Top Section
    3 Results
  • Power Lock Section
    3 Results
  • Oven Body Section
    3 Results
  • Oven Burner Section
    3 Results
  • Top Burner Section
    3 Results
  • Oven Door Section
    3 Results
  • Wire Harnesses And Components
    3 Results
Find part by diagram >

Question and Answers

Q:

9117398710 Kenmore Range - F3 Error

A:

Error codes can be an inconvenience and I will be happy to help. I did some research and I was able to find a link that will provide you with some good information. I hope this helps while you wait for your expert response.

Read More
Joseph P. -
May 21, 2012
A:

Thank you for your question and I understand your concern.

The "F3" fault code indicates an open oven temperature sensor or sensor circuit. The oven sensor is most likely faulty and will need to be replaced. If the fault code recurs after replacing the oven sensor, the electronic oven control is likely faulty. The oven temperature sensor can be disconnected and tested for resistance with an Ohm meter.

The electronic oven control is $338.49 which in my opinion is too much to invest in this older oven. I would consider replacing the oven.

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Read More
Joey S -
Sears Technician
May 22, 2012
See more answers
Q:

Kenmore Gas Range Model 911.7398710.

A:

Owner's manuals are very important to have. While you are waiting on an expert to answer your question, Unfortunately the model number you provided was incorrect a suggestion I have is to verified your model number and add it to this thread so you can get a better answer from the experts!

Read More
Dezeray S -
January 31, 2011
A:

The owner's manual for this older Kenmore gas range is not available online or in hard copy from Sears Parts. I don't have a production date on this model. It was produced before 1987. That is when our online records were downloaded online.

There is not a pilot light on this range. It uses a glow bar igniter system to light the oven burner. The image below shows the theory of operation for that type of ignition system. Your range has the round carborundum igniter. If the igniter is glowing but the burner is not lighting, then the igniter will likely need to be replaced. If the broil burner lights, then you can try switching the broil igniter and the bake igniter to see if the bake burner will light. NOTE: Be sure that you unplug the range before accessing internal components. If the bake burner lights when using the broil burner igniter then replacing the failed igniter will fix this problem.

The part number for the igniter is WB2X9154. You can order that part from the Sears PartsDirect website. Here is a direct link for that part: Ignitor .

If the igniter is not glowing, then you could have a wiring failure in the circuit, a bad igniter or an "open" safety gas valve.

These tips may help you fix the oven burner. If you need more assistance, reply with additional details.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Lyle W -
Sears Technician
February 01, 2011
See more answers
Q:

How do I calibrate my oven temperature?

A:

Taking on a project like this is a challenge to help you I was able to find some information on calibrating which I have attached the links below that can be very helpful. I hope they help!

Read More
Maira -
December 09, 2010
A:

Thank you for your question.

I can understand wanting to calibrate an oven that the temperature is not correct.

The calibration sets are as follows.

  • Push the bake pad and quickly before the relay has a chance to click select a temperature between 500 and 550 degrees and just as quickly push the bake button again.

  • In about 4 seconds double 00 should show in the display.

  • Rotate the knob for + or - up to 35 degrees of off set depending if it is too or too cold of oven.

  • Once done setting the off set push the clock button.

If it is more than 35 degrees off you will need a new control.

This should calibrate the oven to the new setting.

I hope this will help.

Thank you for using Manage My Life.

Read More
Sam A -
Sears Technician
December 10, 2010
See more answers

Top Parts