Model #91149013991 KENMORE ELITE Built-In Oven, Electric

  • Control
    3 Results
  • Wire Harness And Components
    3 Results
  • Center Space
    3 Results
  • Upper Body
    3 Results
  • Lower Body
    3 Results
  • Fan Cover
    3 Results
  • Door Lock
    3 Results
  • Door
    3 Results
Find part by diagram >

Question and Answers

Q:

F7 Error Display

A:

Error codes can means so many things so finding out what it means can be a tough job. While you are waiting on an expert to answer your question, I found some great links in the Manage My Life website. I have attached the links below. Hope this helps!

Read More
Dezeray S -
July 05, 2011
A:

Thank you for your question and I understand your concern.

The "F7" fault code could mean a stuck key pad or it could mean the relay is energized on the oven control board.

Determine if problem is with the Key Panel or Control by:

  1. Pushing CLEAR/OFF pad and then disconnect the power supply from the power source.
  2. Disconnect the Key Panel Ribbon Cable from control and then reconnecting the power supply and waiting at least 32 seconds to see if the Code recurs.
  • If code recurs, problem is in the control. Replace control.
  • If code does not recur problem is with the Key Panel

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
July 05, 2011
A:

Hi there, I have the same model oven and am getting a F2 error code consistently. It appears to be related to the oven temperature going out of control and getting hotter and hotter until the F2 code appears. This also only seems to happen when there is too much space in the oven - ie, either nothing in the oven or only a small item in the oven, with lots of air circulating around it. If there is a large pan covered with food (like a pizza), the oven works fine. Any insight would be so helpful, thanks! My uncle is an electronic engineer and can repair the oven if he knows what the code means and what parts need to be replaced. Best regards and many thanks, Artemis

Read More
Artemis -
November 11, 2011
A:

Artemis: I added an image with the meaning of the F2 fault code. I recommend disconnecting the oven temperature sensor at the oven control board and test the resistance with an Ohm meter. It should measure approximately 1100 ohms at room temperature. If the oven temperature sensor is Okay; it may have faulty oven control board.

Read More
Joey S -
Sears Technician
November 15, 2011
A:

I am getting the f7 error code on my Kenmore double oven mod 911.49013991. We have disconnected the oven from the power source and disconnected the ribbon cable, reconnected it after a minute and the error code recurred. There are two part #s in the manual that have the word 'control' in the description. WB27T10151 - Control Panel w/Keypad, WB27T10140 - Clock/Oven Control. The parts are $466 and $332 respectively so we don't want to order the wrong one. Which part would be the correct one to fix the issue? Thanks.

Read More
Anonymous -
July 28, 2013
A:

Anonymous; If the F7 code displayed with the control panel/touch panel ribbon connector disconnected from the electronic oven control and then powered up, the electronic oven control is faulty. The part number of the electronic oven control board is part #WB27T10287. Part #WB27T10140 substitutes to the new part #WB27T10287.

Read More
Joey S -
Sears Technician
July 29, 2013
A:

Joey, so if the f7 code does not display with the ribbon cable disconnected, can we assume that it's the other part (WB27T10151 control panel w/keypad) that needs to be replaced? Thanks.

Read More
Jan -
July 29, 2013
A:

Jan: That is correct. If the F7 does not recur with the touch panel/control panel ribbon connector disconnected, then it will need a new control panel/touch panel assembly.

Read More
Joey S -
Sears Technician
July 29, 2013
A:

Joey, we performed the test as instructed. With the ribbon cable disconnected and returning power to the oven, the error code displayed was F0. Is this indicative of the same problem, needing oven control board is part #WB27T10287? Or are we getting into a gray area where placing a service call would be the better route? As I stated earlier, we don't want to get burned with a $300-400 part that may not be the right one. Thanks.

Read More
Jan -
July 31, 2013
A:

Jan: The "F0" fault code implies a stuck or shorted key pad. If the ribbon connector is connected to the control board and you push and hold a button too long, "F0" will display. If the key pad ribbon connector was disconnected from the electronic oven control when power was restored and "F0" displayed, the electronic oven control board is faulty. You would diagnose the "F0" just like you would for the "F7" code. The electronic oven control is part #WB27T10287. If you have an doubts, I would call and place a service appointment because the installed part cannot be returned.

Read More
Joey S -
Sears Technician
July 31, 2013
See more answers
Q:

What does error code F7 refer to on a Kenmore 911.4848911 dual oven.

A:

I understand how inconvenient it can be to have an error code on your range since this can keep it from working properly. While you are waiting for an expert answer, I did manage to find some links that will provide you with more information about your problem. Hope these helps!

Read More
Dezeray S -
May 09, 2011
A:

The F7 code indicates a stuck keypad or a relay on the control is stuck in the on position.

The image below may help you with this problem.

Basically you will need to remove the ribbon connector and wait at least 32 seconds to see if the error repeats.

Replacing the control and display should have resolve this problem.

Remember to turn the power off first.

Read More
Fred M -
Sears Technician
May 10, 2011
A:

Our wall oven is 911.49013991. we have been getting a F7 code on the side with the lower oven, but the top oven was still working. Now both ovens don't work. I removed the ribbon and waited, but the F7 code returned. How can I tell if it is the key panel WB27T10151 or the control WB27T10140. Or do I need to replace both. And is this a diy project?

Read More
Alfred -
August 26, 2012
A:

I would suspect the interface will need to be replaced if removing the ribbon didn't help. I would strongly suggest a technician check and repair the problem. The interface is very expensive at approzimately $450 dollars and most electronic parts are difficult to return once opened.

Read More
Fred M -
Sears Technician
August 27, 2012
See more answers
Q:

have a kenmore elite double oven 91149013991, fault code F0,how do i repair

A:

A oven is definitely something we depend on and when it begins to malfunction it can be a huge inconvenience. While you are waiting for an expert to respond, I have attached a helpful link below that may provide information to assist you with your question.

Read More
Barbara H. -
November 10, 2011
A:

If the F0 is being displayed with the oven powered up and the ribbon cable for the control panel disconnected, then the clock control board (part WB36T10463). If the F0 is not displayed with that ribbon cable disconnected, then you will need to replace that control panel (part WB27T10287). You can order the part that you need from the Sears PartsDirect website.

Be sure that you shut off the house circuit breaker for the oven before accessing internal components.

There are situations where both of those components will need to be replaced at the same time to fix this problem.

NOTE: Based on the cost of those parts and the age of the oven, you may consider replacing the oven instead of repairing it. You can view current oven models on the Sears.com website.

Read More
Lyle W -
Sears Technician
November 11, 2011
See more answers

Top Parts