Model #91148485991 KENMORE Built-In Oven, Electric

  • Control
    3 Results
  • Body
    3 Results
  • Door
    3 Results
  • Wire Harnesses/wiring Components
    3 Results
  • Filler Trim Kit 2240505/2240509
    3 Results
  • Door Lock
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Need PN for power connector or wiring diagram 91148485991 Kenmore Built-in double oven

A:

I am 90% certain that I can simply remove the connector, and connect the black and the black with white stripe to House breaker black, white to house breaker white white, and the two reds to house breaker red. Just looking for a confirmation. Thanks!

Read More
Daniel -
February 26, 2014
A:

Note,I took another look and now see that of the two red wires in the connector one of the reds has a black stripe. I am still thinking that the black and black with white stripe connect to house circuit breaker black. and the red and red with black stripe connect to house circuit breaker red, with white to house circuit breaker white (neutral). Please advise, Thanks!

Read More
Daniel -
February 27, 2014
A:

I looked at the wiring diagram for that range. That connector plugs into the Conduit Wire Harness Part WB18K5225. This part does not have an image either but I am confident that it is the part that you need. You can view a drawing of that part on this parts page: Kenmore Oven Model 911.48485991 Body. The conduit wire harness is Key 600 on that page. That harness will have the plug that fits the connector in your image.

The other end of that conduit wire harness will have the wires that connect to your junction box as shown in the Installation Manual.

If you need more help, let us know.

Thanks for choosing Sears PartsDirect.

Read More
Lyle W -
Sears Technician
March 03, 2014
A:

Thank you very much for the research Lyle! The price for that part was a bit high $119. I just cut the end on the connector, attached red to the two primary red wires, black to the two primary black wires, white to white, and green to the frame ground connector on the oven. It has been working great till today that is. All of a sudden we got an F7 code, research seems point out that code comes from a stuck key in the control panel. Any suggestions on that? Thanks in advance Dan

Read More
Daniel -
March 17, 2014
A:

Thank you very much for the research Lyle! The price for that part was a bit high $119. I just cut the end on the connector, attached red to the two primary red wires, black to the two primary black wires, white to white, and green to the frame ground connector on the oven. It has been working great till today that is. All of a sudden we got an F7 code, research seems point out that code comes from a stuck key in the control panel. Any suggestions on that? Thanks in advance Dan

Read More
Daniel -
March 17, 2014
See more answers
Q:

Kenmore Double Oven has power but neither oven heats

A:

It can be a real headache when your oven fails to heat properly. While you are waiting for your expert answer, I did some research on the unit. At this time, I was unable to locate information that would be helpful in regards to your question. Some of these questions that are asked will need specific research and will be answered by an expert with-in two business days but usually sooner.

Read More
Julio -
April 19, 2013
A:

This unit is not covered by warranty now. Sears and Kenmore both refuse to answer any questions online or over the phone. All they would do is send a repairman out and charge me to even look at it.

Read More
Lynn -
April 19, 2013
A:

Thank you for your question and I understand your concern.

Based on your symptom and details, the oven is not likely getting the proper voltage supply.

The first thing that must be checked and verified is the voltage supply. The oven must have a 220-240 volt power source when measuring across line one (L1) and line two (L2).  The oven control only needs 110-120 volts in order to power up but the oven elements must have 220-240 volts. NOTE: I do not recommend measuring the voltage supply unless you have experience and feel safe and confident in doing so; otherwise I strongly suggest calling service technician to diagnose the failure.

If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services.

Read More
Joey S -
Sears Technician
April 22, 2013
See more answers
Q:

Kenmore Double Oven

A:

A oven is definitely something we depend on and when it begins to malfunction it can be a huge inconvenience. While you are waiting for an expert to respond, I have attached some helpful links below that may provide information to assist you with your question.

Read More
Barbara H. -
November 20, 2011
A:

Those links for previous answers that Barbara H. posted in the above response provide some information about the F1 and F7 failures in this type of oven. A stuck key on the control panel or a bad clock control board could be causing your problem. In some situations, a ribbon wire connection problem or corrosion on the contacts of that connection could cause this failure. I recommend that you first try to clear the code by shutting off the house circuit breaker for the oven for 5 minutes. Power the oven back up and see if the code returns. There are times when a power surge or glitch through the electrical lines will cause that clock control board to freeze up. This may reset the oven control so that you can use it normally. This tactic only has a small chance of working but it is worth a try.

If the codes return, I recommend that you shut the house circuit breaker for the oven back off and access the clock control board in the console of the range. You should be able to open the console by opening the oven door and removing the screws at the bottom of that console. Once those screws are removed, you may be able to release the top of the console and carefully fold it down and forward. If that procedure does not work, you may need to pull the oven out of the wall and remove the top panel of the oven behind the console. Check the ribbon cable to make sure that it is properly inserted in the clock control board. I provided information on that control in the image below. Check the ribbon cable for corrosion. You may be able to clean the contacts and resolve this problem without replacing parts if you find corroded contacts. Reassemble the range and then power it up to see if these tactics resolved your problem. If the codes return, then you can follow the procedure in the top of the image below to determine whether your failure is in the control panel or the clock control board. If you need it, I provided an ohm test that you can perform on that control panel keys. This information should help you determine the component that needs to be replaced to fix this problem. You can order parts from the Sears PartsDirect website. Be sure that you shut off the house circuit breaker or remove the house fuses to completely disconnect electrical power before accessing internal components .

If you need more help, reply with additional details and we will assist you further.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Lyle W -
Sears Technician
November 22, 2011
See more answers

Top Parts