Model #9114842996 KENMORE Built-In Oven, Electric

  • Control Section
    3 Results
  • Body Section
    3 Results
  • Door Section
    3 Results
  • Door Lock Section
    3 Results
  • Wire Harness And Components
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

F1 Error, Kenmore 911484-2996

A:

Having a properly working oven is important. I found some information for you that I am hoping will help you out. Please click here:[F1 Error Code]. Your expert will also help answer your question. It may take two business days for your expert to reply. I do hope that everything works out on the Kenmore oven.

Read More
Marc -
August 09, 2013
A:

I know that it can be very difficult to have issues with your oven. That F11 code indicates that you have a bad keypad on the clock control board in the console. You can try to clear that code by unplugging the range for 3 minutes. If the code returns after restoring electrical power, then that clock control board will need to be replaced. However, due to this age of the unit the parts are not longer available. The manufacturer stops producing them after ten years. I hope this helps. If you need further assistance, please reply to this thread. Thank you for using Manage My Life.

Read More
AnneJ -
Sears Technician
August 09, 2013
See more answers
Q:

Neither oven heats up and turns off.

A:

I can appreciate your concern over neither your oven or your broiler heating past 100 degrees.  I did locate a link that might suggest a problem with the sensor.  Click here to view the link.  Though this link discusses a different model number,
the mechanics are likely going to be very similar.  Keep in mind that an expert will be
responding within the next two business days if not sooner and will likely offer you more information and
instruction.  Hope this will be helpful and have a nice day.

Read More
Henry -
June 14, 2013
A:

Thank you for your question. I do understand having a double oven with neither working would be disappointing.  I see Henry provided a link with good information. I did some research and I think this is a different problem. There are two high limit switches that may have tripped. They are safety devices. First the circuit breaker to the ovens should be checked. It may have caused the problem. The fan should be checked to make sure it is working correctly. That may also be why the sensors tripped.  Another possibility is the control since both ovens are affected. To check the thermostat limit switches, first shut off the breaker to the ovens. Remove the two Phillips screws at the top of the control panel. Lower the panel. If the thermostat limit switches read closed continuity with an Ohm meter, then I would check the clock control. If the limit switches read open, they need to be replaced. They are part #'s WB24K5085 and WB24K5033, key number 158 and 159 in the image below and can be ordered at Sears Parts Direct .

If you are not comfortable making these kinds of checks or repairs, I recommend having a technician visit to help.  You can schedule a technician at Sears Home Services. Please reply if further help is needed.  Thank you for using Manage My Life.

 

 

Read More
Barbara H. -
Sears Technician
June 16, 2013
A:

Hello Barbara H, My husband is an electrical engineer so he was able to check the switches with ease. Everything is reading fine. He seems to think it is the control board itself. What do you think of this or do you have other suggestions?

Read More
Janice -
June 19, 2013
A:

Hi Janice. Thank you for the reply. It is great that you have someone who can make these repairs. Yes, the control would be the next item to check. The electrical schematic is usually located behind the control panel. I hope it was, as I was not able to find a readable copy. If the control proves defective, you will need to call Sears Parts Direct for availability of this control.

Read More
Barbara H. -
Sears Technician
June 20, 2013
See more answers
Q:

F3 code 9114842996 Kenmore 27" electric built-in double oven

A:

Appliance error codes can be confusing. I have taken some time to research your question here on the Manage My Life website and I noticed that someone else had asked a similar question with a posted response from an expert. I attached the link below for you to view. I hope the link that I provided is helpful. Have a nice day!

Read More
Yadira B -
October 14, 2012
A:

Thanks But there is not link attached

Read More
judy jackson -
October 14, 2012
A:

Thank you for submitting your question. Yadira has provided you with good information for the F3 error code. Youtube has great videos on how to test the oven temperature sensor. The oven sensor is part number WB21X5301 priced at $74.12. You can order the sensor from our Sears Parts Direct web site. I hope this information helps. Please reply back to this thread if you require further assistance with this repair. If you do not feel comfortable performing test or repairing this problem yourself, I recommend scheduling for service. You can schedule for service online with our Sears Home Services team. Thank you for using Manage My Life.

Read More
Tykara -
Sears Technician
October 15, 2012
See more answers

Top Parts