Model #91147829100 KENMORE Built-In Oven, Electric

  • Control
    3 Results
  • Center Space
    3 Results
  • Upper Body
    3 Results
  • Lower Body
    3 Results
  • Door
    3 Results
  • Door Lock
    3 Results
  • Wire Harness And Components
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

replacing broken glass on lower inside door of 91147829100 dbl oven 91147829100

A:

Thank you for choosing Sears Parts Direct. I will be more than happy to help with your question. Upon researching model 91147829100; it looks like your needing the window kit based on the part number. If you are only replacing the window everything you need will be in the kit.

If you have any further questions please re-post. We appreciate your business. Have a great day.

 

 

 

Read More
Jeff Wallace Jr -
Sears Technician
October 03, 2014
Q:

Having a problem with w double wall oven part # 91147829100 lower cooling fan, need test for it.

A:

I know this type of information can be very helpful for you to have. While you are waiting for your expert answer, I did some research on the unit. I was unable to locate information that would be helpful with regards to your question at this time. Your expert will answer within 24-48 hours with detailed information. Thank you for using Manage My Life.

Read More
Jackie S -
December 26, 2011
A:

There is not a way to check that lower cooling fan through a diagnostic test from the control board. The information on the cooling fans in this oven is shown in the first image below. The second image shows a wiring diagram for your oven with that lower oven fan circuit traced in red. You would need to access that thermal switch and heat it up using a hot air gun to check the actuation of that component. You could check the fan motor by shutting off the circuit breakers for the oven and bypassing that switch (connecting the wires going to the thermal switch together and taping them with electrical tape to prevent them from shorting to the metal cabinet). Once you restore electrical power to the oven with that thermal switch bypassed, that lower cooling fan should run constantly. Shut off the house circuit breakers for the oven and restore the original wiring configuration immediately following that brief test.

This information should help you check that lower oven cooling fan. If you need more assistance, reply with additional details.

If you get to a point where you need to have a service technician diagnose and repair this failure, you can schedule one through this link: Sears Home Services .

Read More
Lyle W -
Sears Technician
December 27, 2011
A:

Lyle, Thanks very much for your help! The top an bottom thermal switches worked as designed and I could heat and cool them to turn on and off the fan circuit. As I suspected, and the schematic confirmed, both fans (are supposed to) turn on if either temp sensor is tripped. New fan has been ordered. It would have been nice if the oven was designed so you could replace it from the front like the top one.

Read More
Bill -
December 27, 2011
A:

I agree with you about that component access issue. I am glad to hear that the information helped. Let us know if you need anything else.

Read More
Lyle W -
Sears Technician
December 27, 2011
A:

Got the fan in, but the part number that was provided on Sears Parts Direct is not exactly the same as the part in the oven itself. Perhaps they upgraded the fan since we bought the unit (2001). Fortunately the motor is the same and you can transfer the old fan blade (which is smaller) and mounting frame to the new motor. The fan just pulls off and the two screws hold the mount. Just transferred these to the new motor and reinstalled. Did the heat gun test on the sensor to make sure the fans worked and reinstalled the unit. Tried to run the self clean cycle but still getting the F9 and F2 error codes after a half hour of running self-clean. Next step is to check the over-temp sensor switch to make sure it is cycling at the right temperatures (240F open / 205F close)and monitor the temperature on it while running the self-clean cycle. The ERC is relatively new so I do not think this is the issue, it seems to be doing what it's supposed to. Question: If the switch is working and the temperature is actually too high in the cavity between the ovens even with both fans is there some other solution? is this a design flaw (too small a fan) with the early versions of this unit?

Read More
Bill -
December 30, 2011
A:

I provided additional technical information for this oven in the images below. It is difficult to read but that is the best reproduction that I have. The F2 and the F9 codes could be caused by an "open" condition in the thermal switch circuit with the yellow leads. The first image shows the wiring diagram that should guide you in checking those circuits. Be sure that you shut off the house circuit breaker to disconnect electrical power before accessing internal components. I am not aware of any design problem with this model. If you need more help, reply with additional details.

Read More
Lyle W -
Sears Technician
December 30, 2011
See more answers
Q:

Can I use my Kenmore oven model 911.47829100 without light bulb cover?

A:

You can use the oven without the light cover although I recommend replacing it as soon as possible.

Read More
Joey S -
Sears Technician
November 30, 2009

Top Parts