Model #91147649100 KENMORE Built-In Oven, Electric

  • Control Panel
    3 Results
  • Upper Body
    3 Results
  • Center Spacer
    3 Results
  • Lower Body
    3 Results
  • Upper And Lower Door
    3 Results
  • Lock
    3 Results
  • Wire Harnesses/components
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

I have a Kenmore Double Oven Model 911.47649100. No response from key pad other then clera/off button, Time is still on display. No

A:

I seen that someone asked a similar question. I understand having a appliance give you trouble is very hard. While you are waiting on an expert to answer your question. I found this really great link on error codes. I attached the link below. Hope this helps! Good luck.

Read More
Dezeray S -
September 08, 2010
A:

Thank you for your question.

  • I would suggest that disconnect the power for 1 minute and then re-connect power to the oven.

  • Try to reset the time of day and check the functions of the key pads.

  • If they work ok, you have solved the problem.

  • If it still is not working you will need to replace the touch pad. You can order the part from Sears Parts Direct .

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

I hope this helps.

Thank you for using Manage My Life.

Read More
Sam A -
Sears Technician
September 09, 2010
A:

I have the same unit and have had to replace the touch pad twice. If you press the key pad to hard ( cleaning it ) it will damage it.

Read More
Gary -
July 27, 2013
See more answers
Q:

lower oven of a double oven does not work.

A:

Good morning..... I can understand your concern and you've done a good job at trying to get to the bottom of this problem. I've provided a link below that will bring up a parts diagram for your particular oven. I will forward your question to an expert who will investigate the matter further and get back to you. You will hear from them within two business days if not sooner. Until you hear from us, have a nice day.

Read More
Henry -
February 08, 2013
A:

Based on your details, I suspect that the high limit safety thermostat on that lower oven is tripped. I circled that component on the wiring diagram in the image below. That thermostat is located on the outside back panel of the lower oven. You can view the parts diagram for the oven on this page: Kenmore Wall Oven Model 911.47649100 Parts. The high limit thermostat is Key 157 on the Lower Body page of that diagram.

You can shut off the house circuit breakers to completely disconnect electrical power and pull the oven out of the cabinet. Use the installation guide to help you with that task if necessary. Here is a copy of the installation instructions in case you need them: Installation Instructions . Remove the outer back panel in the middle of that lower oven to access the high limit thermostat. Here is a link for that thermostat so that you can see what it looks like and order a replacement if necessary: Limit Switch for Kenmore Wall Oven 911.47649100. You can check that limit switch with a volt/ohm meter. It should measure near zero ohms of resistance. If the component is "open" (measure OL -- open load or infinite resistance) then it will need to be replaced.

If the high limit thermostat (limit switch) is okay, then you could have a wiring failure or a problem with the electronic control board.

Reply with additional details if you need more help with this failure.

If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link:  Sears Home Services. 

Read More
Lyle W -
Sears Technician
February 08, 2013
A:

I want to thank Lyle W. for his expert guidance on my double oven problem. He is very good and straight to the point Thanks again.

Read More
larry149 -
February 08, 2013
See more answers
Q:

Control panel is dead.

A:

I understand the concern when it comes to disconnecting the ribbon cable on the control board of your range. While you are waiting for an expert to respond, I have attached a helpful link below that may provide information to assist you with your question.

Read More
Yadira B -
January 31, 2013
A:

Thank you for your question and I understand your concern.

Based on your details, the flat ribbon should simply pull out once the two locking tabs on each end of the connector has been depressed or placed in the unlocked position.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
February 01, 2013
See more answers