Model #91147489991 KENMORE Built-In Oven, Electric

  • Control
    3 Results
  • Door Lock
    3 Results
  • Body
    3 Results
  • Wire Harnesses/wiring Components
    3 Results
  • Door
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Kenmore oven flashing f2 91147489991

A:

Thank you for choosing SearsPartsDirect. I will be more than happy to assist you with your Kenmore oven.

From the information you have provided above, I can understand the frustration of having your oven malfunction, after researching model number 911.47489991. The "F2" error code indicates that oven temperature was sensed being over 615 degrees with the door lock circuit in the unlocked mode, or it sensed an oven temperature above 915 degrees with the door in locked mode.

This could be caused by:

Welded relay contacts. (Heating elements on in off mode)

An open thermal switch in the lock circuit.

Thermal switch not closing.

Cooling fan stalled.

High resistance in the oven sensor probe.

Electrical noise interference in the sensor circuit (Ham radio, cordless telephone, etc.

I recommend calling a service technician to diagnose and repair your range.

 

I hope you found this information useful. Again thank you for choosing Sears, we appreciate your business, have a great day.

*Safety disclaimer before you try and repair the unit make sure the power supply is disconnected. There may be sharp parts to the unit that can cause injury to you if not careful. If you don’t not feel comfortable checking this yourself you can request a technician by visiting www.SearsHomeService.com*

Read More
Benny23 -
Sears Technician
June 13, 2015
Q:

F3 error on Kenmore electric oven 911-47489991

A:

Thank you for choosing SearsPartsDirect.com and being a valued member.  I can certainly understand how frustrating it can be when your  range is displaying an error code. 

F3- Open or shorted sensor (circuit). Could be a result of contamination on terminals or pinched wire in sensor circuit, cold solder joint in control.

Disconnect power to range. DIsconnect sensor connector from control.
Measure sensor resistance at control connector (take care not to damage terminals in block)- should read 1100Ω at room ambient aprox. 72 °.F.
Measure each sensor lead from connector block to ground. If shorted, look for pinched or cut wire in cicuit.
Check connector terminals- look for deforemed or corrosion on terminals. Repair or replace. 
If all above is Ok replace control. 

F5- loss of relay drive circuit.
Check sensor for intermittant high resistance. 
Press clear/off and reprogram control. If f5 code reappears, replace control.

You can also visit searpartsdirect.com for parts, diagrams, and repair information.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for your question. Have a great day. 

Read More
Natasha12 -
Sears Technician
December 23, 2014
Q:

replacing oven elements 91147489991 Kenmore 27

A:

Thank you for choosing SearsPartsDirect.com and being a valued member.  I can certainly understand how frustrating it can be when needing to replace the elements in your oven.

It is usually that simple, but you would need to make sure the unit is unplugged and turned off before installing any part.

 
The first thing to do is to REMOVE POWER FROM THE WALL OVEN.

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact your local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Open the oven door and locate the retainer screws that hold the element to the oven cavity back wall.

Remove these screws and also remove the ceiling support for the broil element.

Once you have these removed pull the element forward and down to gain access to the wires and wire terminals on the end of the element. Make sure you have pulled enough wire through into the oven cavity to gain access to the screws that secure the wires to the element.

Carefully remove the connections and once removed install the wire connections onto the new element and hold the terminal with one hand while carefully tightening with the other hand and tool. (Do not bend the fitting on the end of the new element).

Re-install the broil element into the back wall of the oven and re-secure the broil element support in the ceiling of the oven.

 

You can also visit searpartsdirect.com for parts, diagrams, and repair information.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for your question. Have a great day. 

Read More
Natasha12 -
Sears Technician
November 07, 2014

Top Parts