Model #91147489890 KENMORE Built-In Oven, Electric

  • Control
    3 Results
  • Wire Harness And Wiring Component
    3 Results
  • Body
    3 Results
  • Door Lock
    3 Results
  • Door
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

I have a Kenmore wall oven model #911-47489890. We have been getting error code F2. Do we replace the p/n wb27t10276 (face plate)

A:

I understand that your Kenmore wall oven is displaying the error code F2 on its display. While you are waiting for an expert to respond, I have attached some helpful links below that may provide information to assist you with your question. Have a great day!

Read More
Alina F. -
June 22, 2012
A:

Based on that model number, I am not showing that the control part WB27T10276 is compatible with your Kenmore wall oven. The original control board part WB27T10064 would need to be removed and sent to Core Centric Solutions for repair if that component is causing this F2 problem. Here is a link for that Core Centric Solutions website in case you need it: Core Centric Solutions.com .

Depending on your exact symptoms, you could have a bad oven temperature sensor (part WB21X5301) that would cause this failure. You can shut off the house circuit breakers for the oven and access that sensor as shown in the image below. Here is a link for a brief repair video that shows how to test that sensor using a volt/ohm meter. That sensor problem should measure around 1100 ohms at room temperature. If the resistance of that sensor is significantly higher than that, then you may be able to fix this failure by replacing that sensor probe. Here is a link for that part: Kenmore Wall Oven 911.47489890 Sensor Probe .

Be sure that you shut off the house circuit breakers for the oven before accessing internal components.

If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services .

NOTE: Based on that age of that wall oven and the availability of repair parts, you may consider replacing that oven instead of repairing it.

Read More
Lyle W -
Sears Technician
June 25, 2012
See more answers
Q:

Fault code on oven

A:

Error codes can be a great help to warn of appliance issues but difficult to get information about. I was able to locate two similar questions that may help while you wait for the expert response. I attached the links below. I hope this information helps.

Read More
Barbara H. -
February 23, 2012
A:

Thanks for the information, now all I have to do is figure out how to get to it

Read More
John -
February 23, 2012
A:

As indicated in those previous answers, that F7 is often caused by a bad control key panel. That first image below shows a procedure that you may be able to use to release that console in your oven. Be sure that you shut off the house circuit breakers for the oven to completely disconnect electrical power before accessing internal components. Your oven may not be exactly like the one shown in that first image but the basic procedure is the same if that control panel can be removed from the front of the oven. I you are not able to release that console in that manner, then you will need to carefully pull the oven out of the cabinet and access that control through the top panel behind that console (with the house circuit breakers for the oven shut off ). Unplug the ribbon wire connection on that control board and then reassemble the oven and power it back up. If that F7 reappears then you will need to remove that clock control board and send it to Core Centric Solutions for repair. Here is a link for that website that has contact information: CoreCentricSolutions.com . A repair of the control board costs around $150.

If that F7 does not reappear, I recommend that you clean the contacts on the ribbon connector and then plug that ribbon connector securely back into the clock control board. Power the range back up and see if it works properly. Corrosion on the contacts will sometimes cause that F7 code. If that does not help, then you will probably need to replace that control panel. If you want to test that control panel, you can use the information in the second image.

If the control panel is bad, you can order a replacement panel from the Sears PartsDirect website. The part number will depend on the color that you need. The part number for the black panel is WB36T10482. The white panel is part WB36T10171. The almond color panel is no longer available.

I hope that this information helps. If you need more assistance, reply with additional details.

If you get to the point where you need to have a service technician complete this repair, you can schedule service through this link: Sears Home Services .

Read More
Lyle W -
Sears Technician
February 24, 2012
A:

Worked like a champ. Front came of as described, cleansed the ribbon connector, seems to working just like it is supposed to. Thanks for the tip.

Read More
John -
February 25, 2012
A:

Thanks for letting us know how this turned out. We are glad to hear that the oven is working again. Let us know if you need more help.

Read More
Lyle W -
Sears Technician
February 27, 2012
See more answers

Top Parts