Model #91147485890 KENMORE Built-In Oven, Electric

  • Control
    3 Results
  • Wire Harness And Wiring Component
    3 Results
  • Body
    3 Results
  • Door Lock
    3 Results
  • Door
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

My Kenmore Built-in Elec Oven keeps beeping and indicating F7 (in red). How do I get it to stop beeping? Its model no. 91147485890. Help!

A:

When it comes to error codes on appliances trouble shooting is the most important thing to do. While you are waiting on an expert to answer your question, I found a great link in the Manage My Life website on your error code. I have attached the link below. Hope this helps!

Read More
Dezeray -
March 30, 2013
A:

The F7 error indicates a failed oven control board or stuck keypad.  Press the Clear/Off.  Let oven sit for about an hour, then key in an oven operation command.  If you are comfortable doing more, carefully disconnect the ribbon from the control panel, reinstall, wait about 32 seconds and if error returns, replace the control. If the error does not return, the the problem was in the keypad.  The model number for the control panel is #WB36T10171(white) or #WB36T10170 (black) at Sears Parts Direct .  If you would like a technician to make checks and replace the control panel if needed, you can schedule a Sears technician at Sears Home Services .  If further assistance is needed, please reply.  Thank you for using Manage my Life.

Read More
Barbara H. -
Sears Technician
March 30, 2013
See more answers
Q:

Have a Kenmore 27" Electric Built in Oven.tried to self-clean

A:

Having your built in oven lock and not be able to open it can be very frustrating. I did some research and provided a link to a similar question and answer on our site. I hope this will give you a better idea on the next step to take until the Expert responds to your question in more detail within 24 to 48 hours.

Read More
Julio -
October 27, 2012
A:

Thank you for your question and I understand your concern.

The "Locked Door" will flash while the door is being locked. Once the door is locked the "Locked Door" will remain illuminated in the display. Since "Locked Door" is flashing, the door lock assembly has not likely reached the full locked position or it has a faulty door lock assembly or possibly a faulty electronic oven control board. The door lock assembly is located above the oven behind the control panel. Since there is no way to remove the control panel with the door locked, you can likely access the door lock assembly by removing the oven and then taking the top panel off. You would have to remove the mounting screws securing the door lock assembly and then manipulate the door lock and release it from the door and then open the door. NOTE: Flip the house circuit breakers off dedicated for the oven before removing the oven and top panel.

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Read More
Joey S -
Sears Technician
October 29, 2012
See more answers
Q:

Kenmore Control Oven T09

A:

I think its great that you are wanting to do some repairs on your own. I would suggest that you provide a little more information such as the make and complete model number of your product, so your expert will be able to provide you with the best possible answer. Just click on reply down below, where you can provide the additional information.

Read More
Joseph P. -
January 10, 2012
A:

Kemore, Model #911.47485890

Read More
Hosie -
January 10, 2012
A:

The original control board for that oven was WB27T10064. I am not showing information that indicates the WB27T10864 was a designated substitution for that original control board part WB27T10064.

The WB27T11276 is listed as a valid substitution for control board WB27T10864 but I do not see it listed as a valid substitution for part WB27T10064. If you did have that WB27T10864 installed as you indicated and it was working then you may be able to wire up the new control board WB27T11276 using the wiring diagram shown in the image below. If you are unsure about how to wire that control board, I recommend that you have a service technician install that new board. Here is a link for the Sears Service website: Sears Home Services .

If you want more help in resolving this problem yourself, reply with more information including the answers to these questions if possible:

  • How did you determine the part number for the WB27T10864 board that you indicated was currently installed in the range?
  • Did that control board WB27T10864 have a part number label on it?
  • Was the control board in that oven previously replaced during a service call or repair?
  • How does the control board WB27T11276 differ from the control board that you currently have installed (Send digital pictures of the boards if possible)?

We will try to assist you further once we receive more information.

Read More
Lyle W -
Sears Technician
January 12, 2012
A:

Thanks for your response. I had incorrectly entered the wrong part number, when I ordered the replacement part. You are correct on the part number for the model number for the oven I have. Thanks again.

Read More
Hosie -
January 19, 2012
A:

Thanks for letting us know what you found. We are glad to hear that you resolved this problem. Let us know if you need more help.

Read More
Lyle W -
Sears Technician
January 19, 2012
See more answers

Top Parts