Model #91146756590 KENMORE Slide-In Range, Electric

  • Control Panel Section
    3 Results
  • Wire Harness
    3 Results
  • Main Top Section
    3 Results
  • Door Lock Section
    3 Results
  • Body Section
    3 Results
  • Blower Section
    3 Results
  • Door Section
    3 Results
  • Optional Kits
    3 Results
Find part by diagram >

Question and Answers

Q:

How to access control panel on slide in range?

A:

Do it yourself repairs can be intimidating on new model appliances but with a little help from experts it becomes much easier. I located a previous expert post with direction for a similar model that may help while you wait for your expert to review and respond. I attached the link below along with the link to Sears Parts Direct for your model if parts or schematics are needed. Hope this information helps.

Read More
Barbara H. -
August 28, 2011
A:

Thank you for your question and I understand your concern.

I added an image below with the instructions on how to access the controls. NOTE: Disconnect the range from the power supply before accessing the controls.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
August 30, 2011
A:

Thank you so much for your help. You just saved me the price of a new range. The instructions were great and they made it a very easy task. I found the problem and now the range is working perfectly. Thankfully, Phil

Read More
Phillip Wells -
August 30, 2011
See more answers
Q:

After running self clean cycle, display reads lock and can't open oven door. model 911.46756590

A:

The self cleaning feature on ranges is great. Most of us will put up with a lot to not have to scrub out the oven with oven cleaner. I can see you followed the normal procedure to start another clean cycle. While you wait for the expert to review your model, you might check two other expert posts I attached below for help.

Read More
Barbara H. -
May 21, 2011
A:

Thanks for the asist, tried both of those links and nothing worked.

Read More
Jason -
May 21, 2011
A:

bump

Read More
Jason -
May 22, 2011
A:

Fixed it, couldn't afford new lock motor, so I removed the piece that locks the door, and switch two ground wires on the lock motor fooling it into thinking it is unlocked, works now, just can't use self clen until I get a new motor.

Read More
Jason -
May 22, 2011
A:

Thank you for your question and I understand your concern.

The door may not be unlocking because of a faulty oven door lock, door lock switches or possibly because of a faulty oven temperature sensor or control board.

Program and start another clean cycle and then wait 2 minutes and then cancel the cycle and then wait to see if the door locking assembly will operate and unlock the door. If it will not unlock the door then the door lock assembly will need to be tested. I added an image below showing where the door lock assembly is located and how to access it. _NOTE: Disconnect the range from the power source before accessing the door lock assembly.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

I highly recommend calling a service technician to diagnose and repair your range.

Read More
Joey S -
Sears Technician
May 23, 2011
See more answers
Q:

What does the F3 error mean on my Kenmore electric range?

A:

This is an issue you can fix yourself. The F3 indicates the oven sensor is bad. You can test the oven sensor. Begin by disconnecting the power to the range and removing the rear panel covering the ERC. Remove the back panel from the range and follow the oven sensor wires up to the control. Disconnect the plug on the ERC containing the oven sensor wires and read the resistance of the oven sensor. It should read between 1000-1200 ohms.

If the oven sensor tests within this range the ERC is defective. If it tests out of the range disconnect the wires from the oven sensor and measure the resistance of the oven sensor. If it tests out of the range the oven sensor is defective. If it tests within the range the harness between the ERC and the oven sensor is defective.

Always unplug or de-energize electrical equipment before removing covers or attempting service. The oven temperature sensor is located in the oven cavity in the upper left rear corner or the rear upper right corner. The oven temperature sensor probe can be removed and disconnected from inside the oven cavity and tested with an Ohm meter. Pull the sensor into the oven approximately 10 inches for access to the quick disconnect. The oven sensor should have a resistance measurement of approximately 1100 ohms at room temperature. If the oven sensor does not have approximate resistance of 1100 ohms, replace the sensor; click here Sears Parts Direct If the sensor ohms at approximately 1100 ohms then you will need to reconnect it and then make the same test up at the control board by disconnecting the sensor harness plug and rechecking the resistance across the two sensor wire leads. If it measures approximately 1100 ohms there, replace the control board click here; Sears Parts Direct

If you require further assistance please resubmit question with details of the checks you have made. I will be looking forward to helping you again in the near future.

Read More
Landell -
Sears Technician
January 22, 2010

Top Parts