Model #91146755590 KENMORE Slide-In Range, Electric

  • Control Panel Section
    3 Results
  • Wire Harness
    3 Results
  • Main Top Section
    3 Results
  • Door Lock Section
    3 Results
  • Body Section
    3 Results
  • Blower Section
    3 Results
  • Door Section
    3 Results
  • Optional Kits
    3 Results
Find part by diagram >

Question and Answers

Q:

In the panel of my stove/oven the "broil lock" light is on. Oven not working.

A:

Thanks for contacting manage my life about your range /oven model 91146755590; sorry you are having this problem with its operation, I will be glad to assist you. Based on the description you have provided I think that the oven lock system has stuck, indicating that the door is locked when it is actually open.  Here is something you can do that may release the switch inside the latching system.  At the oven cavity top you will see a small hook (it may be recessed into a slot in cavity of oven.  If you can get a hold of this hook with a tool just try moving it back and forth up and down gently, this may release the switch and operations will be okay again.  (However if you use the clean cycle or door locking feature this could reoccur)   The locking mechanisms can be replaced, but if it is cost effective would need to be considered.  I hope this helps, if you need more help reply with added details and I will be happy to respond. If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services.Ron H.

Read More
Ron H -
Sears Technician
September 25, 2013
Q:

Kenmore Model# 91146755590 Sensor reads 1116

A:

Understanding readings like 1116 on Kenmore ranges can tell us what is wrong with the range. Are there any error codes that come up that begin with E or F? Please submit additional information as to what is wrong with the range, so we can get you the best possible answer. Click on reply with additional information.

Read More
Anna T -
May 30, 2012
A:

Yes this first started with the F 3 code and the oven going off. I can get it to come back on but it goes off again. It did the F 2 last night when I had finised keeping going then I cut it off the F 2 came on a few minutes later by itself beeping

Read More
Eddie -
May 30, 2012
A:

Hello Eddie. It looks like I have been helping you with this problem in this thread: f3 code . Your last comment on that thread seems to indicate that you received the help that you needed. If you need more assistance, let us know. Thanks.

Read More
Lyle W -
Sears Technician
June 01, 2012
A:

Lyle your help has been very useful. Although it has led me to a conclusion I was hoping to avoid right now. But at least now I can use the money I would have used on trial and error towards a new range. Thanks, Eddie

Read More
Eddie -
June 01, 2012
See more answers
Q:

f3 code

A:

I understand how inconvenient it is to have an error code on your range. While you are waiting for an expert answer, I did manage to find a link that will provide you with more information about your problem. I hope my link is useful.

Read More
Joseph P. -
September 22, 2010
A:

The F3 code on this type of range indicates that you have a problem with the oven temperature sensor probe circuit. This is often caused by a bad oven temperature sensor. It can also be caused by a wiring problem in the circuit. Since you replaced the control board, I recommend that you unplug the range (or shut off the breaker) and check the wiring connection for the temperature sensor. You can measure the resistance through that circuit with a volt/ohm meter. The sensor circuit resistance should be about 1100 ohms at room temperature. If you do not measure that resistance through the circuit, I recommend that you check the resistance directly at the sensor probe in the oven. The image below shows how to access this component (with the range still unplugged). Measure the resistance directly at the sensor. If it does not measure around 1100 ohms at room temperature then it will need to be replaced. If it does measure the 1100 ohms, then you likely have a damaged wiring harness between the sensor and the control board. You can splice in new wiring with ceramic wire nuts to fix this type of problem.

If you need more help, reply with additional details and we will assist you further.

Read More
Lyle W -
Sears Technician
September 24, 2010
A:

tested sensor ok ,tested wiring ok, is there any fuse links somewere nobody is talking about.

Read More
paul -
October 01, 2010
A:

If the wiring circuit was okay then there is not a blown fuse in the sensor circuit. If you reply with the full model number of the range, I can try to find a wiring diagram for it and verify that you have the correct clock/control board. I did not find any Kenmore ranges with that exact series of number (46581) in it. I recommend that you recheck that model number and give us an update.

Read More
Lyle W -
Sears Technician
October 02, 2010
A:

Thanks for the suggestions. I also saw where you can switch off the power when the code goes off. I tried that and so far it seems to be working! Thanks again.

Read More
Dave -
October 17, 2011
A:

Thanks for that feedback Dave. Disconnecting electrical power will reset that control board. This will sometimes clear that error code as it did in your situation. I am glad to hear that disconnecting power resolved your F3 problem. If the code reappears and you need more help, let us know.

Read More
Lyle W -
Sears Technician
October 18, 2011
A:

I have took my sensor out and measured it disconnected it reads 1116 does this mean it is bad?

Read More
Eddie -
May 30, 2012
A:

Hello Eddie. The sensor should measure around 1100 ohms at room temperature. That sensor is in the ball park range that is should be. That resistance would not cause an F3 assuming that you have the same model mentioned above (or a similar model that uses the same type of sensor). Most of the sensors for oven measure around 1100 ohms at room temperature but there are a few that are different. I recommend that you plug the sensor back into the harness and check the resistance of that sensor circuit directly at the control board in the console (with the range still unplugged or the breakers shut off). If the resistance through that entire circuit is around 1116 ohms then the control board will probably need to be replaced. If the resistance through that entire circuit is different than the 1116 ohm reading then I recommend that you check the wire harness for problems. The most suspect part of that wire harness is the disconnect plug at the sensor. You can often fix a harness problem by cutting off that disconnect plug and connecting those wires properly using ceramic wire nuts. I hope that this information helps. If you need more assistance, reply with additional details and the full model number of your range.

Read More
Lyle W -
Sears Technician
May 31, 2012
A:

Thank you. Model# 91146755590 30" slide in model. Do you have picture of the control board. I checked the sensor again last night before I put it in and got a read of 1096. When I put it back together I ran the stove and it seems like it is intermitten. sometimes it codes F3 sometimes F2 and sometimes it way just stay on. Sometimes if I just hit the clear button and turn back on it will show that temp has dropped and show a quick rise and then code again.

Read More
Eddie -
May 31, 2012
A:

Hello Eddie. That control board is Key 16 in the parts image shown below. The second image shows how to access the control board in the console. Be sure that you SHUT OFF THE HOUSE CIRCUIT BREAKER before accessing that control board or other internal components. The third image shows a wiring diagram and other information that should help you check that sensor circuit. If the sensor circuit is okay, then you will probably need to remove that board and send it to Core Centric Solutions for repair. That replacement part for the control board is no longer available but the control board can be repaired by that company. I added a link below that has contact information for Core Centric Solutions. I hope that this additional information helps. If you need more assistance, let us know.

Read More
Lyle W -
Sears Technician
June 01, 2012
See more answers

Top Parts