Model #9114672992 KENMORE Slide-In Range, Electric

  • Control Panel Section
    3 Results
  • Wire Harness
    3 Results
  • Main Top Section
    3 Results
  • Door Lock Section
    3 Results
  • Body Section
    3 Results
  • Blower Section
    3 Results
  • Door Section
    3 Results
  • Trim Extension 8078690
    3 Results
  • Backsplash
    3 Results
  • Rear Main Top Filler
    3 Results
Find part by diagram >

Question and Answers

Q:

Kenmore Glass Top Range

A:

Ranges are appliances we count on daily so when it comes to your appliance not working properly it can be really concerning. While you are waiting on an expert to answer your question, I suggest you set service with a Sears technician. I have attached the link below. Have a nice day!

Read More
Dezeray -
July 23, 2012
A:

When you're ready to use the oven on the Kenmore range and it does not work properly, it can be frustrating. Managemylife.com is here to help. It is important to know what numbers are flashing which can tell us more of what is going on with the range. Just click on reply to continue the thread.

Read More
Anna T -
July 23, 2012
A:

Thank you for your question and I understand your concern.

Based on your symptom and details it sounds like a voltage supply issue. The line one (L1) could be dropping out under the current load or it could be loosing the Neutral (N) line or L1 at the clock/oven control. A voltage meter will be needed in order to check the static voltage and when the oven is turned on to see if the voltage supply is dropping out under current load. The voltage should be measured at the terminal block where the power supply is connected to the back of the range. Flip the two house circuit breakers off dedicated for the range before sliding the range out and removing the terminal block cover. You may even find a burnt or loose wire connection at the terminal block. NOTE: I do not recommend making any voltage measurements unless you have experience and feel safe and confident in doing so; otherwise I strongly suggest calling a service technician to diagnose and repair your range.

This may be the issue. If not, please reply and I will be glad to assist you further.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
July 24, 2012
See more answers
Q:

Need dimensions for Kenmore slide in range #911-4672992

A:

I see you need the dimensions for your Kenmore Slide in Range. While your waiting on an expert answer, you can contact Sears.com and they can give you the dimensions information. I attached the link below, I hope this helps!!!!!!

Read More
Raquel F -
August 16, 2010
A:

Thank you for your question.

  • This is a standard 30 inch slide-in range with the controls in the front. Since this range sits on the floor like a standard range the dimensions are the same with the exception that it does not have a back splash like a standard range.

  • The dimensions should be 29 7/8 wide to fit a 30 inch opening.

  • The back top of the range would require a filler strip if the opening was not made for a slide-in. The filler strip usually comes with the new range, and used only if needed.

Read More
Sam A -
Sears Technician
August 17, 2010
See more answers
Q:

F1 error code flashes & beeps on Kenmore Electric Slide-In range. What is wrong?

A:

error codes can be confusing, it would be so much easier if it was displayed on the appliance. I researched your question and found someone asked a question similar to yours. Here is what was posted by an expert, I have provided the link below. I hope this helps!

Read More
Jacqueline S -
August 15, 2010
A:

The F1 error code is an internal control failure and if will not cancel you will need to have the ERC (clock) replaced. FIRST; disconnect power to the range. The ERC is no longer available on this model & will have to be pulled & sent in for repairs. Please call 630-588-1700 for shipping instructions.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact your local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Read More
biker dave -
Sears Technician
August 16, 2010
See more answers