Model #91146564011 KENMORE Slide-In Range, Electric

  • Main Top
    3 Results
  • Body
    3 Results
  • Door
    3 Results
  • Door Lock
    3 Results
  • Blower
    3 Results
  • Wire Harness And Components
    3 Results
Find part by diagram >

Question and Answers

Q:

My Kenmore Electric Stove Coil Element won't heat up.

A:

I am understanding the issue that is on hand on the stove. This website is great to have when you are needing specific information answered. I was unable to find any specific information for you. The model number that you supplied is incorrect. I was not sure of what type of cook top you had. So please if you can add to this thread the model number that's on the item itself.

Read More
celene -
April 15, 2011
A:

Thank you for the quick response and Please note that the model number is indeed correct. Kenmore 911.46564011 I checked it on my stove itself and also you can find more information at searspartsdirect website aswell. Maybe try removing the (.) and look for 91146564011 and it is a Kenmore Electric Range Top I bought back in 2002. Once again I thank you for your time and appreciate all your help.

Read More
Hiral -
April 15, 2011
A:

Thank you for your question and I understand your concern.

You mentioned current but you did not mention voltage. The surface elements require 220-240 volts in order to heat properly. The surface element switch needs to have L1 voltage (120 volts) and it must have L2 voltage (120 volts). When the surface element switch is turned on, there must be 120 volts supplied to H1 and 120 volts supplied to H2 which is the circuits connected to the surface element receptacle. You will need a volt meter to check and verify voltage (220-240 volts) when measuring across L1 and L2 on the switch and you will need to check and verify 220-240 volts when measuring across H1 and H2 on the switch. If you measure 220-240 volts across L1 and L2 and your not measuring 220-240 volts across H1 and H2, replace the burner switch. I added an image below of the surface element circuit.

NOTE: I do not recommend checking and confirming voltage unless you have experience and feel safe and confident in doing so, otherwise I recommend calling a service technician to diagnose and repair your range.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
April 18, 2011
See more answers
Q:

NEED HELP WITH CHANGING MAIN COOKTOP WIRE HARNESS ON KENMORE RANGE TOP (Model: 911.46564011).

A:

A non working Oven is not something any of us want to see. If you are technically handy, this is a good site to get instruction and fix some things yourself. If you do not feel confident doing your own repairs, an option is to visit Sears Home Services and use the scheduler. While you wait for the expert to review your model, you can check the bottom links for some possibilities. Hope this is of help.

Read More
Priscilla V -
April 10, 2011
A:

The wire harness on your range seems to be in pretty good shape. I think you could cut the wires behind the discoloration on the wires and install new terminals on the existing wire.

If you have a soldering iron, it would be good to solder the new terminals on the wires.

To replace the wiring harness, begin by disconnecting the power to the range.

Before disconnecting the wires from the switches, take pictures for rewiring. You will probably need to remove the old wiring harness to have room to install the new one. Route the wires in the same position the old wires were routed.

The wires go out the back of the burner box and back underneath the burner box to the switches mounted in the control panel. I would remove the bottom of the burner box to remove the old wire and run the new wire.

Install the new wire terminals on the switches in the same manner the old wires were installed. Install the new terminals on the cooktop as the old ones were installed.

I am sending you some images from the mini manual that was in the range from the factory. This is as close to a manual as we have.

I apologize for the quality of the images. I hope you can read them.

Read More
Jimmy K -
Sears Technician
April 12, 2011
See more answers

Top Parts