Model #9114652191 KENMORE Slide-In Range, Electric

  • Main Top Section
    3 Results
  • Optional Backsplash 8059091
    3 Results
  • Body Section
    3 Results
  • Wire Harnesses And Components
    3 Results
  • Door Lock Section
    3 Results
  • Optional Rear Main Top Filler 8028790
    3 Results
  • Blower Section
    3 Results
  • Optional Vertical Trim Extension 8078690
    3 Results
  • Oven Door Section
    3 Results
Find part by diagram >

Question and Answers

Q:

Help with codes F2, 3, 4 etc .. info misplaced electric drop in range .. 20 yrs old

A:

Managemylife.com is always a great resource to find the answers to just about anything. I have done some research for you but I was unable to locate any useful information for you at this time. An expert will research your question and respond within two business days but usually sooner. Have a great day!

Read More
Alina F. -
June 23, 2012
A:

I know that it can be very difficult to have issues with your range. Based on your details the oven temperature sensor or the oven temperature sensor wiring circuit is bad or loose. The "F2, F3, and F4" all point to an oven temperature sensor or an oven temperature sensor circuit failure. The oven sensor circuit will need to checked and tested using an ohm meter. The oven temperature sensor can be found protruding into the oven cavity in the rear upper right or left hand corner.

The oven temperature sensor should have a resistance measurement of approximately 1100 ohms at room temperature. I recommend checking the resistance where the sensor connects at the control board if it test OK at the sensor. If it test OK at the control board, the control board has failed. If the sensor does not measure 1100 ohms at room temperature, replace the sensor. The image below will provide the wiring diagram you need.

If you would still like a copy of the owner's manual, just click on this link: Owner's Manual . I hope this helps. If you need further assistance, please reply to this thread. Thank you for using Manage My Life.

Read More
AnneJ -
Sears Technician
June 26, 2012
See more answers
Q:

range model # 9114652191 have f01 error cannot set clock hard reset not working sometimes i can mess with button and use oven is it still safe to use

A:

Managemylife.com is always a great resource to find the answers to just about anything. I know this information can be very helpful for you to have. While you have been waiting for your expert to respond, I did some research and I was able to locate this information that should be helpful with regards to your question at this time. Your expert will be answering you within two business days but usually sooner. Thank you for using Manage My Life.

Read More
James -
February 11, 2012
A:

Thank you for your question and I understand your concern.

The "F1" fault code indicates a failed component on the electronic oven control (ERC). The electronic oven control will need to be replaced. I recommend having the electronic oven control replaced before attempting to use the oven.

The electronic oven control will need to removed and shipped out for repair because there are new ones available.

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Read More
Joey S -
Sears Technician
February 13, 2012
See more answers
Q:

Kenmore model 911.4652191 dimensions.

A:

Wanting to know the dimensions on your appliance is always great to know. While you are waiting on an expert to answer your question, a suggestion I have is to visit Sears Parts Direct website to speak with a Sears technician so they can tell you the dimensions on your appliances. Hope this helps!

Read More
Dezeray S -
August 15, 2011
A:

Thank you for your request for the information on the slide in range.

This is a standard 30 inch slide in range.

Any 30 inch slide in range will fit in your location.

30 inch slide in range .

I did not find any with standard coil burners; they are all smooth top ranges.

Thank you for using Manage My Life

Sam A.

Read More
Sam A -
Sears Technician
August 16, 2011
See more answers