Model #9114652190 KENMORE Slide-In Range, Electric

  • Main Top Section
    3 Results
  • Optional Backsplash 8059091
    3 Results
  • Body Section
    3 Results
  • Wire Harness And Components
    3 Results
  • Door Lock Section
    3 Results
  • Optional Rear Main Top Filler 8028790
    3 Results
  • Blower Section
    3 Results
  • Optional Vertical Trim Extension 8078690
    3 Results
  • Oven Door Section
    3 Results
Find part by diagram >

Question and Answers

Q:

recalibration 9114652190 Kenmore Slide-in range

A:

Thank you for contacting ManageMyLife.com on how to recalibrate the oven in your Kenmore slide-in range. I'm happy to help you today. The instructions for adjusting the temperature in the oven are locate on page 21 of the owner's manual. If the manual has been misplaced, I included a direct link to it below.

Owner's Manual 

The oven will only allow you to adjust the temperature by a maximum of 35 degrees. If the temperature in the oven is 150 degrees off, the control won't adjust that much and it is possible that the control will need to be replaced. Looking into the parts list, I see that the control board is no longer available. The control board itself will need to be take out of the range and sent in to be repaired. This is something a technician will need to do. Here is a link to the parts list diagram for the main top section. If you click on the control board in the list (key#16) more parts information will be provided.

If you would like to have the control board sent in for repair, service can be scheduled at the following link: Sears Home Services.

I really hope this information helps you today. Thank you for using ManageMyLife.com.

Read More
Korinna S -
Sears Technician
October 08, 2013
Q:

The oven does not get hot enough! 9114652190 Kenmore Slide-in range

A:

Thank you for your question. I am sorry you are having problems with the oven. I can see you have made the repairs usually responsible. I would also check the oven sensor probe, part #WB20X0106 at Sears Parts Direct .  This is at the back of the oven cavity. Be careful when disconnecting, to not let the wires connections drop behind the back panel. If it is malfunctioning, that is the cause. Don't forget to also do a oven recalibration.  This should be done after any repairs. The image is below. Also remember to make sure the clock is set.  The oven will not operate correctly if the clock is not set. If further help is needed, please reply.  Thank you for using Manage My Life. 

Read More
Barbara H. -
Sears Technician
October 05, 2013
Q:

Why does my Kenmore electric range model 911.4652190 flash F1 and continuously buzz?

A:

The F1 indicates a failed transistor in the oven control board. It is not likely that you can reset the control to clear this fault code and problem. You can try shutting off the breaker for the range for 5 minutes and then restoring power to the range. If the condition still exists, then the oven control board will need to be replaced. The part number for your control board is WB27K5073. This part is discontinued and no longer available through Sears PartsDirect. You may be able to find a source for the part by using a web search engine such as Google.

If you find this control and want to replace it yourself, you should be able to access it by disconnecting electric power to the range (shut off the breaker) and raising the cook top panel. This will give you access to the back side of the control console.

Read More
Lyle W -
Sears Technician
A:

I have had the same problem, generally trip the breaker and restart. I noticed this was first ask in Dec. 08, have you come up with a answer since?

Read More
charles -
October 04, 2013
See more answers