Model #9114558819 KENMORE Drop-In Range, Electric

  • Control Section
    3 Results
  • Main Top Section
    3 Results
  • Body Section
    3 Results
  • Door Lock Section
    3 Results
  • Oven Door Section
    3 Results
  • Wire Harnesses And Components
    3 Results
  • Optional Porcelain Pan And Chrome Ring Kit No. 8068400
    3 Results
Find part by diagram >

Question and Answers

Q:

Oven on my kenmore drop in range wont work, but the cook top does

A:

Thank you for your question and I understand your concern.

Based on your symptom and details, I would suspect a faulty electronic oven control/clock assembly. There is also a relay board used to close the bake and broil relays too which also could be faulty. The clock/oven control tells the relay board to close the bake or broil relays. If the control does not indicate the oven is programmed for bake and returns to time of day, I suspect it may have a faulty clock/oven control. The oven control/clock assembly is part # 342136R which can be ordered from Searspartsdirect.com

Based on the information at Searspartsdirect.com, at this time this part is only available through Sears Home Service. If you would like to have this part installed by Sears Home Service, please call 1-800-4-MY-HOME or click here to schedule an appointment for the repair.

Based on the age of the range, you may want to consider replacing the range rather than having it repaired. It could wind up costing more than expected to have it repaired depending on the failure(s).

If you get to the point where you decide to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services.

Read More
Joey S -
Sears Technician
October 15, 2013
Q:

my Kenmore oven will not heat.

A:

Having an important kitchen appliance like a range begin to give you error codes can be very frustrating. I did some research and provided a link to a similar question and answer on our site. I hope this will shed a little more light on the issue until the Expert responds to your question in more detail within 24 to 48 hours.

Read More
Julio -
August 27, 2012
A:

I know that it can be very difficult to have you oven stop working properly. The "F3" fault code indicates an open oven temperature sensor or sensor circuit. The oven temperature sensor has likely failed.

The oven temperature sensor will need to removed and disconnected and tested for proper resistance. The oven temperature sensor probe should measure approximately 1100 ohms at room temperature.

The oven temperature sensor is located inside the oven cavity. It can be found protruding into the oven cavity in the upper left rear corner or in the upper right rear corner. It will be held in place with a couple of screws. Remove the screws and slowly pull it out and then disconnect the wires. If you find that it does not measure with approximately 1100 ohms or resistance, or if it measures open/no continuity, replace the temperature sensor probe. The part number of the sensor is WB21X5301 which can be ordered from Sears Parts Direct I added a YouTube video showing how to test the oven temperature sensor

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
AnneJ -
Sears Technician
August 27, 2012
See more answers
Q:

What does the F-1 and F-2 mean on my range?

A:

The "F1" is a failed oven control board. The "F2" is an over temperature failure. Both is likely cause by the oven control, however it could also have a faulty oven temperature sensor probe along with a failed oven control. The oven control is part #WB19X255R at $219.99 and the oven temperature sensor probe is part #WB21X5301 at $73.49

I recommend replacing the range rather than having it repaired.

Read More
Joey S -
Sears Technician
September 25, 2009