Model #9114554190 KENMORE Drop-In Range, Electric

  • Control Section
    3 Results
  • Main Top Section
    3 Results
  • Body Section
    3 Results
  • Wire Harness
    3 Results
  • Door Lock Section
    3 Results
  • Blower Section
    3 Results
  • Oven Door Section
    3 Results
Find part by diagram >

Question and Answers

Q:

f4 error 9114554190 Kenmore 30

A:

Thank you for choosing sears I would be happy to help you with your range. Upon researching model 9114554190; to access the temperature sensor unplug the oven power cord and make sure you can access the back of the unit. Open the oven door and remove the racks from the inside of the oven and remove the screws that hold the sensor to the back of the oven. You will now have access the temperature sensor.

 

I trust this information will help you, have a great day.

Read More
CarlosZ -
Sears Technician
February 17, 2015
Q:

Why is the 4 month old ERC on my Kenmore range beeping F2 over & over again?

A:

The F2 code indicates that the ERC detects an oven over-temperature condition through the resistance of the oven sensor circuit. Since this is happening when the oven is not even on, it is apparent that the problem is either in the sensor circuit or the electronic control board. There are some factors that can cause a false F2 to be displayed. Here are some issues that could cause this problem:

  • Electrical interference such as a cordless telephone plugged into the same circuit as the range could cause a false F2.
  • Strong signals (such as from a ham radio in the vicinity) can be picked up by the sensor wire harness and cause the F2.
High resistance through the sensor wiring or a failed temperature sensor probe could also cause this problem.

The sensor circuit is connected to the ERC on the 6-pin connector on the side of the board. If you are able to shut off the breakers for the range to disconnect electrical power and access the ERC, you can check the resistance of the sensor circuit wiring through the connection on the board. The sensor circuit is on the pins 4 and 6 that are separated by a space. Unplug this connection (with electrical power disconnected) and measure the resistance with a volt/ohm meter. You should measure about 1100 ohms at room temperature. If resistance is high (over 1300 ohms), then a failed temperature sensor probe or a wiring problem would be causing this failure. If you are able to access the temperature probe and check the resistance directly at the probe, you can determine whether the failure is in the probe or the wiring. If you are not able to safely access these components, I recommend calling a service technician to diagnose and repair this problem.

Read More
Lyle W -
Sears Technician
A:

tappan stove 30-3860-23/03 f 2 code had temp sensor checked room temp 1100 ohms want to know if by heating with torch will ohms change? trying to test under heat to make sure part is good before replacing clock timer

Read More
randy -
May 30, 2012
See more answers
Q:

9114554190 --- f 1 code can i fix this myself and do i need parts and if so what type of parts ? what is f1 code

A:

Our Kitchen is the heart of our home. I'm sorry to hear that you are having some difficulties with your Kenmore Range. I did some research for you at Managemylife and found an expert answer to a similar question that may help until your expert can respond to your specific question. The link is attached below. If you do decide to schedule service and have a qualified technician help you, I have also attached a link to Searshomeservices. I hope these links provided assist you.

Read More
James -
February 07, 2012
A:

You can try to reset the control by shutting off the house circuit breaker for the range for 3 minutes. If you restore power and still see that F1 code then the clock control board in the console will need to be removed and sent to CoreCentric Solutions to be repaired (about a $150 repair). That F1 indicates that a transistor in that clock control board has failed. The replacement part for that control board is no longer available. That is why the clock control board would need to be removed and sent off for repair. Here is a link for that control board repair center that has contact information: CoreCentric Solutions.com . To remove that control board, you will need to shut off the house circuit breaker for the range to completely disconnect electrical power . Follow the procedure shown in the image below to access that clock control board in the console.

If you need more help, let us know.

If you get to the point where you need to have a service technician complete this repair, you can schedule service through this link: Sears Home Services .

Read More
Lyle W -
Sears Technician
February 07, 2012
See more answers

Top Parts