Model #9114552192 KENMORE Drop-In Range, Electric

  • Control Section
    3 Results
  • Main Top Section
    3 Results
  • Body Section
    3 Results
  • Wire Harness And Components
    3 Results
  • Door Lock Section
    3 Results
  • Blower Section
    3 Results
  • Oven Door Section
    3 Results
Find part by diagram >

Question and Answers

Q:

Blinking door lock light 9114552192 Kenmore Drop-in range, electric

A:

Thank you for choosing SearsPartsDirect.com. I will be more then happy to assist you. Even though the oven door lock is physically open, the electronic oven control board is detecting that it is still locked. The control board detects the position of the door lock through the switch. If this switch is stuck or broken, it could be causing your problem. Push the off/cancel button and see if the lock motor runs. Disconnect power from the range for 1-2 seconds and see if that helps. If the control won't respond, then you may need to replace the door lock assembly or the electronic oven control. If you are able to access the door lock mechanism, you can check the switch for continuity. If you measure a closed condition (near zero resistance), then the door latch assembly will need to be replaced. This should fix this problem. If the door latch assembly tests good, then you will likely need to replace the electronic oven control board. If you are not comfortable doing this repair you can Click Here to schedule a technician or call toll free 1-800-469-4663. Hope this information has help you, any further questions or concerns. You will have to post a new question because at this time I can not reply to any comments. Thank you for choosing SearsPartsDirect.com.









 

Read More
Samantha A -
Sears Technician
May 29, 2014
Q:

what does code f2 and f 3 mean 9114552192 Kenmore Drop-in range, electric

A:

Hello glad to help.  Thank You for choosing Sears PartsDirect.com

I am sorry and do understand your frustration when there is trouble with the range.

Glad to help out.   Im  looking at your Kenmore model number 911.4552192.

These 2 codes are very similar.   F2 error code is theh oven temperature sensor is getting too hotor mayb shorted.   F3 error code: Oven too hot and needs to replace the oven temperature sensor.

Oven temperature sensor for model 911.4552192 

 If you have further questions please let me know.

Thanks for choosing Sears PartsDirect.com

Read More
Larry L -
Sears Technician
November 26, 2013
Q:

Drop in range not working?

A:

The oven not heating properly can ruin your baked goods and I am sorry for the inconvenience. I did some research and I was able to find two links that will guide you with your repair. I hope this helps while you wait for your expert response.

Read More
Joseph P. -
May 10, 2012
A:

Thank you for your question and I understand your concern.

First, make sure that both oven elements are working.

Generally speaking, the thermometers you�re using take a long time to actually display the correct temperatures. Allow the oven to cycle a couple of times before checking the temperature readings on the thermometers. If the oven is still not reaching the set temperatures, you can adjust the oven temperature by following the instructions I added in the image below.

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Read More
Joey S -
Sears Technician
May 12, 2012
A:

Joey, Thanks for giving me some ideas to check. When you say "both elements Working", I'm assuming you mean the top and bottom elements. I never checked elements when the oven preheated before. I thought just the bottom element was use for baking. Anyway, when preheating, the bottom element had a nice glow, but the top element never came on. When the oven indicated it was preheated to 350, both oven thermometers registered about 300. After 5 minutes, the oven thermometers were up to around 325. Then after another 5 mins., the bottom element came on again, the oven thermometers were down to a little under 300. When the bottom element went off, another 5 mins. or so, the thermometers were back up to around 300. After I turned off the oven, I turned the broiler on and the top element had a nice glow, so I'm figuring the broiler works. Do I now adjust the oven temp. or, even though the broiler works, is the top element not working properly? I appreciate your patience with me and help. Thanks, Nick

Read More
Nick -
May 15, 2012
A:

Nick: Based on your reply and details, the oven elements are working. You will not see the upper/broil element glowing red when it alternates with the bake element; only when broiling. I recommend increasing the oven temperature 10 degrees using the instructions in the image I provided earlier. This will likely resolve the baking issues.

Read More
Joey S -
Sears Technician
May 15, 2012
A:

Joey, we increased the temp 10 degrees, however when we used the oven last night it was still off by almost 50 degrees. When it initially preheated the oven and both thermometers were very close. When I checked after around 15 minutes the oven and thermometers were at that 50 degree difference and stayed that way for the last 15 minutes of baking. When I raised the oven temp and all 3 went up, but kept the difference. I hope the 18 years is not catching up with the oven. Again, thanks for your help.

Read More
Nick -
May 19, 2012
A:

Nick: If your certain the oven is not heating up to the set temperature and you have off set the temp using the information I provided earlier, the oven control or oven temperature sensor is likely faulty. If you have an Ohm meter the oven temperature sensor probe can be removed and tested for the proper resistance using the Ohm meter. The oven temperature sensor should measure approximately 1100 Ohm of resistance at room temperature. The sensor is located inside the oven cavity on the back wall. The sensor is part #WB21X5301 and the electronic oven control would have to be removed and sent in for repair. It may be time to replace the oven. The control is about $180.00 and the sensor is about $75.00

Read More
Joey S -
Sears Technician
May 19, 2012
A:

Thanks for all your help. We figure after 18 years it probably is time to replace it. We don't really want to start spending money on an 18 year old stove. We do appreciate all your help. Have a good day. Nick

Read More
Nick -
May 20, 2012
A:

Nick: You made the correct decision in replacing the 18 year old range. Thank You for using Manage My Life.

Read More
Joey S -
Sears Technician
May 21, 2012
See more answers