Model #91142719100 KENMORE Counter Unit Electric

  • Maintop
    3 Results
  • Wiring Harness
    3 Results
Find part by diagram >

Question and Answers

Q:

I have a kenmore cook top #911.42719100. & I need to know how to install part #WB24T10026. Please help.

A:

Managemylife.com is always a great resource to find the answers to just about anything. Your expert will research your question and respond within two business days but usually sooner.

Read More
Alina F. -
December 30, 2011
A:

That WB24T10026 is a burner switch for an element on that cook top. There is not a specific procedure for that repair. You may be able to use the parts diagram that is shown in the image below to help you access the burner switch. Here are some basic steps that may help you complete this repair:

  1. Pull the knob off the burner switch that you are replacing.
  2. You will need to shut off the house circuit breakers or remove the house fuses for the cook top to completely disconnect electrical power .
  3. You can then pull the cook top out of the counter.
  4. You will need to remove the burner box box or the bottom panel of the burner box to access the burner switches in the control box of the cook top.
  5. Note the location of the wires on that burner switch. Label them or take a digital picture to document their location so that they can be properly connected on the new burner switch.
  6. Disconnect the wires.
  7. Remove the old switch and mount the new one.
  8. Properly connect the wires.
  9. Reassemble the cook top.

Test the burner to see if it works properly. If you need more help, reply with additional details and we will try to assist you further.

Read More
Lyle W -
Sears Technician
December 31, 2011
A:

Thank you Lyle for your response. The fellow who put my question in must have misunderstood the problem. The problem is when the new switch came in it was a different manufacturer and the numbers identifying the terminals are different from the switch that i am replacing. I need to know the which numbers the wires go to on the new switch. any help you can give is greatly appreciated. Thank you; Bill

Read More
Bill -
December 31, 2011
A:

The images below show the wiring schematic and wiring diagram for that cook top. That information may help you wire up that new switch. The part information that I see on that switch indicates that it should be the same as the original switch. If you are not able to use the information shown below, reply with details about the terminals on the old switch and the new one. Check the actual part numbers that are physically labeled on the old switch and new one if you can find that information. We should be able to help you wire up that replacement switch once we have that information.

Read More
Lyle W -
Sears Technician
January 02, 2012
A:

Thank you very much Lyle for all your help. I installed the new switch and it works good. One thing you may want to note, the new switch's terminals are located differently from the old one and the wiring harness for the indicater light is about an inch short. A jumper is needed to complete the hookup. Thank you again for your help and we wish you a Happy and Blessed new year. Bill

Read More
Bill -
January 03, 2012
A:

Thanks for that additional information Bill. We are glad to hear that you got that switch connected properly. We also hope that you and yours have a Happy and Blessed New Year.

Read More
Lyle W -
Sears Technician
January 03, 2012
See more answers
Q:

Why is one burner on my Kenmore cook top not getting hot?

A:

The rear center element likely needs an infinite burner switch since it will not regulate the temperature. If it does not cycle off occasionally due to the thermal limiter switch opening then the element may also need to be replaced.

The burner that is not heating needs to be diagnosed by a technician to determine whether the problem is in the switch, the element or the wiring.

Since you have several problems with this cook top, I recommend that you have a service technician repair it. Here is a link for the Sears Service website: Sears Home Services .

Read More
Lyle W -
Sears Technician
February 18, 2010

Top Parts