Model #91141889890 KENMORE Built-In Oven, Electric

  • Control
    3 Results
  • Wire Harnesses And Components
    3 Results
  • Center Space
    3 Results
  • Upper Body
    3 Results
  • None
    3 Results
  • Lower Body
    3 Results
  • Door Lock
    3 Results
  • Door
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

91141889890 error F-0 i replaced board twice still getting this error?

A:

I understand that you are getting the error code F0 displayed on your oven. While you are waiting for an expert to respond, I have attached a helpful link below that may provide information to assist you with your question. I hope this is helpful. Have a great day!

Read More
Alina F. -
May 29, 2012
A:

Thank you for your question and I understand your concern.

The "F01" fault code indicates a shorted or stuck (OFF) key. The "F01" fault code could be caused by the electronic oven control board or by a faulty touch panel/console assembly.

To determine which one is faulty; disconnect the oven from the power supply. Disconnect the flat ribbon connector from the electronic oven control board and place the Ohm meter leads across pins 13 and 14 and it should measure open. Press and hold the (OFF) key and the Ohm meter should measure 100-150 Ohms of resistance. If it measures 100-150 Ohms of resistance without pushing the (OFF) key, replace the touch panel/console assembly. The key pad/control panel is offered in the colors of black and white. You can look up the one needed at Sears PartsDirect .

Since you have already replaced the control board we can rule out that being the cause. Replace the control panel and it should resolve the "F0" fault code.

Check the things I have covered here and if I may be of further assistance as more details become available, please reply to this post.

Read More
Joey S -
Sears Technician
May 30, 2012
A:

Pins read 48.6 and 51.8 when off is held.

Read More
eddie -
May 31, 2012
A:

Eddie: What was the resistance without pushing the OFF button? I suspect a faulty touch panel since replacing the oven control board twice did not resolve the issue.

Read More
Joey S -
Sears Technician
June 01, 2012
See more answers
Q:

What's going on with my oven?

A:

Having the range up and working is essential. The error codes can definitely be aggravating. I found some information for you that I am hoping will help you. I am adding the link below to help you with your question while you wait for your expert response. It may take 24-48 hours. I do hope that this will help you with the oven.

Read More
Alina F. -
May 29, 2012
A:

Thank you for submitting your question and I'd be happy to assist you with your range. The F7 error code indicates that a key touch pad is making contact for to long (stuck key). This is usually caused by a failure on the overlay touch pad on the control panel. It will require that you replace the touch panel. The panel is part number WB36T10168 (white) priced at $371.49. You can order parts from our Sears Parts Direct team. It appears that you can remove the screws at the top of that console and then release it and fold it down to access the control board. If you do not feel comfortable performing test or repairing this problem yourself, I recommend scheduling for service. You can schedule for service online with out Sears Home Services team. I hope this helps. Thank you for using Manage My Life.

Read More
Tykara -
Sears Technician
May 31, 2012
See more answers
Q:

My oven was showing F0 I replaced control now showing F0 and F7. I just disconnected control ribbon for 23 sec and replaced Do you think it is the key pad?

A:

Having the range up and working is essential. The error codes can definitely be aggravating. I found some information for you that I am hoping will help you. I am adding the link below to help you with your question while you wait for your expert response. It may take 24-48 hours. I do hope that this will help you with the oven.

Read More
Marc H -
May 29, 2012
A:

Thank you for your question and I understand your concern.

I provided an answer to your first question in the link below.

91141889890 error F-0 i replaced board twice still getting this error?

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Read More
Joey S -
Sears Technician
May 30, 2012
See more answers

Top Parts