Model #91141489991 KENMORE Built-In Oven, Electric with Microwave

  • Body
    3 Results
  • Door Lock/wire Harness/components
    3 Results
  • Door
    3 Results
  • Microwave Enclosures
    3 Results
  • Microwave Control Panel
    3 Results
  • Microwave Door
    3 Results
  • Microwave Body
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

power requirements for Kenmore oven micro combo model 911.41489991 911.41489991

A:

Thank You for choosing Sears PartsDirect.com. Glad to help out. Im looking at your model number 91141489991 and you may want to contact your local electrical technician for these concerns you have. It requires a 50 amp breaker. This oven must be connected to a supply circuit of the proper voltage and frequency as specified on the rating plate. Wire size must conform to the National Electrical Code or the prevailig local code. The rating plate is located in the microwave cavity on the left side. Yes 12-3 is too small. I recommend having a electrician inspect and wire the unit correctly for you. I hope this information helps.  If you have further questions please resubmit your question for further information.

 
Thank you for choosing Sears PartsDirect.com.
 
SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact Sears for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.
 

Read More
Sherman_G_Wallace -
Sears Technician
July 24, 2014
Q:

Replacing a heating element in an electric range

A:

I know this type of information can be very helpful for you to have. While you are waiting for your expert answer, I did some research on the oven. I was unable to locate information that would be helpful with regards to your question at this time. Your expert will answer within 24-48 hours with detailed information. Thank you for using Manage My Life.

Read More
Barbara H. -
December 23, 2011
A:

Thank you for your question and I understand your concern.

Replacing a heating element in your model range is a simple procedure. The first thing to do before removing the element is to disconnect the wall oven from the power supply. Remove the screws securing the element to the rear panel and then remove the element slowly until you can disconnect the wires. Be careful and do not let the wires recoil back through the opening or you may not be able to see or reach the wire. Disconnect the two wires by pulling on the metal female spades and not by pulling on the wires. Re-connect the wires on the new heating element and remount the element. NOTE: Be care when pulling the connectors off the terminals so not to make them fit loose. If they fit loose; use a pair of pliers and gently squeeze the female terminal together just a little so it fits tight when you push the female spades back onto the element terminals.

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Read More
Joey S -
Sears Technician
December 23, 2011
See more answers
Q:

bake element replacement

A:

A combination built in oven with microwave like you have does sound like it may be more complicated to repair. I can see how easy it would be with limited access to have this happen. At this point, if you want to have an expert technician complete repairs and give you peace of mind, an option is to visit Sears Home Services and use the scheduler. If you want to move on with the repair yourself, whileyou wait for the expert to answer, you can check a previous post I found that has a wiring diagram. Bear in mind, it is not your model. I attached below if it will help. http://www.managemylife.com/mmh/questions/220999-kenmore-oven-bake-element-wont-work-replacement-1 http://www.searshomeservices.com/

Read More
Barbara H. -
October 31, 2010
A:

Thank you for your question.

This is always my biggest fear when I replace an element. If one of the element wires did not come out with the element, the whole oven has to be pulled out of the wall. Then the back panel removed and the wire located. Once the wire is located you can feed it back into the hole or connected to the element if has already been installed. I have found the installation manual on the website. The file is too big to post on this site. I will send the instructions to the email we have on hand. Make sure to turn the power off to the oven before you start the repair.

If you run into problems, please reply below.

Here is a link to order any parts you need. Sears Parts Direct .

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for using Manage my life. Mark T.

Read More
Mark T -
Sears Technician
November 01, 2010
See more answers

Top Parts