Model #91141165791 KENMORE Built-In Oven, Electric

  • Control Section
    3 Results
  • Wiring Components
    3 Results
  • Center Space Section
    3 Results
  • Upper Body Section
    3 Results
  • Body Section
    3 Results
  • Door Lock Section
    3 Results
  • Door Section
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Difficulty of replacing control panel on wall oven

A:

I can understand your frustration over the trouble your are experiencing while trying to replace the control panel on your oven. While you are waiting for your expert answer, I did some research on the unit. At this time, I was unable to locate information that would be helpful in regards to your question. Some of these questions that are asked will need specific research and will be answered by an expert with-in two business days but usually sooner.

Read More
Julio -
May 07, 2013
A:

Thank you for your question and I understand your concern.

The "F1" fault code can imply a stuck or shorted key pad or it can imply a relay is turned on on the control board. 

 A service technician would diagnose if the failure is with the Key Panel or Oven Control by:

 

  1. Pushing CLEAR/OFF pad.
  2. Disconnecting Ribbon Cable from the control and waiting at least 32 seconds to see if Code recurs.

 

 

  • If code recurs, problem is in the control. Replace control.
  •  If code does not recur problem is with the Key Panel.
This is procedure is performed with the power supply on and I do not recommend attempting to proceed in the steps above unless you have experience and feel safe and confident in doing so, otherwise I recommend calling a service technician to diagnose which one is faulty.
 
To remove the control panel; DISCONNECT POWER, remove three screws across the bottom of the control panel and push up to release the top corners.

 

The oven control appears at this time is only available through Sears Home Service. If you would like to have this part installed by Sears Home Service, please call 1-800-4-MY-HOME. The control panel is offered in two colors. Since I do not know which color is needed, you can look up and order the part at Searspartsdirect.com
 
 
Read More
Joey S -
Sears Technician
May 09, 2013
See more answers
Q:

wiring a clock control

A:

When it comes to substituted parts for the Kenmore range, things look different but work the same when you get assistance from an expert. The link provided below is on a similar question. Hope this helps while waiting for additional information. If you decide on service, that link is also provided.

Read More
Anna T -
January 06, 2013
A:

There are 2 different versions of Kenmore ovens that begin with model 911.41165 . . . according to the technical information that I see. The model 911.41165690 uses that control board WB27T10292 that you referenced in your details. The model 911.41165791 uses the control board part WB27K5301. It can also use a substitute control board that is part number WB27T10228 (or WB27T10228R is the refurbished version of that control board). According to your details, it is likely that you have the wrong control board for your model of range. If you have the model 911.41165791 then you will need to use control board WB27K5301 or WB27T10228 (as noted above, the refurbished part WB27T10228R will also work). I posted the wiring schematic and a drawing of the original control board in the images below. This information may help you resolve that problem in your oven. If you need more assistance, reply with additional details and the full model number of your oven.

If you get to the point where you need to have a service technician replace the control board in that oven, you can schedule service through this link: Sears Home Services .

Read More
Lyle W -
Sears Technician
January 08, 2013
A:

Here are the images.

Read More
Lyle W -
Sears Technician
January 08, 2013
See more answers
Q:

I need know what wire by color connects to which connector by location in the clock control.

A:

Step by step instructions that the experts do so well here at Manage My Life. The expert will review and respond within 24-48 hours if not sooner so you can complete the repair. Have a great day.

Read More
Barbara H. -
February 19, 2012
A:

I don't have instructions for wiring that new control board part WB27T10228R. I do have the wiring diagram and wiring schematic for that range. Those documents are provided in the first 2 images. The third image shows the original control board that was installed in that oven. That information may be useful in wiring that new control if you have instructions that came with that new control board. To help you further, we will need more information. If you received an instruction sheet with that control board, reply with a document number for that instruction sheet if possible. We could also help you more effectively if you sent us a digital picture of the new control board so that we can see the E4, E5, E6, E7 and E8 connectors. Reply with additional information and we will try to assist you further.

This may be a difficult control to install on your own since it is a revised part. If you get to the point where you need to have a service technician install that control board, you can schedule service through this link: Sears Home Services .

Read More
Lyle W -
Sears Technician
February 21, 2012
See more answers

Top Parts