Model #91141165690 KENMORE Built-In Oven, Electric

  • Control Section
    3 Results
  • Door Lock
    3 Results
  • Door Section
    3 Results
  • Center Space Section
    3 Results
  • Upper Body Section
    3 Results
  • Wire Harnesses And Components
    3 Results
  • Lower Body Section
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

we are getting locked door message/ no heat 91141165690 Kenmore Built-in oven, electric

A:

Thank you for choosing Sears Parts Direct. I will be happy to help with built in oven. Upon researching model 91141165690; unplug it for at least five minutes to do a reset. If lock door still flashes then the lock motor could have failed in the locked position. I linked a diagram below showing the lock assembly. The motor is number 151 in the diagram.

Thank you for choosing Sears. Have a great day.     

Read More
Jeff Wallace Jr -
Sears Technician
October 11, 2014
Q:

wiring a clock control

A:

When it comes to substituted parts for the Kenmore range, things look different but work the same when you get assistance from an expert. The link provided below is on a similar question. Hope this helps while waiting for additional information. If you decide on service, that link is also provided.

Read More
Anna T -
January 06, 2013
A:

There are 2 different versions of Kenmore ovens that begin with model 911.41165 . . . according to the technical information that I see. The model 911.41165690 uses that control board WB27T10292 that you referenced in your details. The model 911.41165791 uses the control board part WB27K5301. It can also use a substitute control board that is part number WB27T10228 (or WB27T10228R is the refurbished version of that control board). According to your details, it is likely that you have the wrong control board for your model of range. If you have the model 911.41165791 then you will need to use control board WB27K5301 or WB27T10228 (as noted above, the refurbished part WB27T10228R will also work). I posted the wiring schematic and a drawing of the original control board in the images below. This information may help you resolve that problem in your oven. If you need more assistance, reply with additional details and the full model number of your oven.

If you get to the point where you need to have a service technician replace the control board in that oven, you can schedule service through this link: Sears Home Services .

Read More
Lyle W -
Sears Technician
January 08, 2013
A:

Here are the images.

Read More
Lyle W -
Sears Technician
January 08, 2013
See more answers
Q:

How do I fix my Kenmore oven model 911.41165690?

A:

According to your similar question, the problem that you are having appears to be the F7 error code. This is normally caused by a failed control touch panel on the console (parts numbers for the two colors were provided in your other answer). In rare situations, the failure can be caused by a failed electronic oven control board (part WB27T10292). There is also a slight possibility that a connection problem with the ribbon cable from the control touch panel to the electronic oven control board is causing this problem.

The normal method of checking for the failed component is to shut off the breaker (or pull the house fuses) for the oven and then access the control board in the console of the oven. The image below shows how to open the console and access the control board. Check the ribbon connection on the control board to make sure that it is plugged in properly and is secure. If it is then use this test to determine the likely component failure:

Pull the ribbon connector for the control touch panel and then reassemble the oven and power it back up. Wait at least 1 minute to see of the F7 code recurs with the ribbon cable for the control touch panel unplugged from the control board. If the code returns on the display then the control board (WB27T10292) will need to be replaced. If the code does not return, then the control touch panel will need to be replaced.

NOTE: You should only attempt to fix this problem yourself if you are completely confident in your technical ability to properly shut off electrical power to the oven and safely access the components in the control.

This will be an expensive fix if a component needs to be replaced in this oven even if you order the failed part and replace it yourself.

If you need more help, resubmit your question with additional details.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Lyle W -
Sears Technician
March 17, 2010

Top Parts