Model #91141069690 KENMORE Built-In Oven, Electric

  • Control Section
    3 Results
  • Wire Harnnes And Components
    3 Results
  • Body Section
    3 Results
  • Door Lock
    3 Results
  • Door Section
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

What does F2 error code mean on my Kenmore oven

A:

It can be very frustrating when your range malfunctions and display error codes. I did some research and provided a link to a similar question and answer on our site. I hope this will shed a little more light on the issue until the Expert responds to your question in more detail within 24 to 48 hours.

Read More
Julio -
January 17, 2013
A:

Thank you for your question. This F2 code indicates an over temp condition. I'm attaching the information below. Now, there is a good chance that the oven temperature sensor has failed. The oven sensor can be tested using an ohm meter. The sensor will need to be disconnected and tested for resistance with the ohm meter. The sensor should have a measurement of 1100 ohms at room temperature. It's located protruding into the oven cavity from the back wall at the top. Disconnect the power first and then remove the screw holding the sensor in place and pull it out far enough to access the wires. Disconnect the wires and now check the sensor resistance. If it's more than 5% off, replace the sensor. I hope this will help you. If you would like more assistance, reply to this thread and I will be glad to assist you further.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Scott D -
Sears Technician
January 19, 2013
See more answers
Q:

i have a f2 on my oven

A:

Error codes on appliances can mean so many different things. While you are waiting on an expert to answer your question, I found a great link in the Manage My Life website on your error code. I have attached the link below. Have a nice day!

Read More
Dezeray -
August 20, 2012
A:

just off top of your head can u give me a ballpark figure on cost for an ocu oven control unit ? i dont have the model# handy but i can tell u i can bye a whole new stove just like the kenmore we have for arroud 375.00 installed and dev. for free this will try to tell you on giving me a $ on ocu , its one of kenmores cheapest ovens with electronic temp controls .

Read More
adam dykstra -
August 20, 2012
A:

Thanks for choosing ManageMyLife to assist you with this F2 error code issue. This error code can indicates an over temperature condition either in self-clean or bake mode. 95% of the time this requires replacing the EOC, electronic oven control. I am sending you the service manual information covering other possibilities that may cause the F2 error code. Please click on the attachment below for more information. You can try to clear this code from the directions provided in the attachment.

If you decide to have a qualified technician to assist you with this repair, you can Click here to set service on line at the Sears Home Services web site.

I want to suggest that you provide the make and model number of your product so we can perform the best research on this. If you have more questions,or can provide the make and model # please log back into the ManageMyLife, go to the homepage, Click on your profile. This will direct you to your profile page. Scroll down to the bottom of your profile page until you see "(your name) conversations" Click on your question. you'll see "Join this conversation" from there, you can reply back to me by adding more details, then Click "reply" This is the fastest way to respond to me.

Read More
James -
Sears Technician
August 21, 2012
A:

My model is 91141069690 with an F2 error code

Read More
Jody -
January 17, 2013
See more answers
Q:

Door Locked.

A:

Managemylife.com is always a great resource to find the answers to just about anything. Your expert will research your question and respond within two business days but usually sooner.

Read More
Alina F. -
December 30, 2011
A:

The oven door will not unlock until the oven cools down to a reasonable temperature.

If the oven is at room temperature, then you could have a number of different failures that would prevent the oven door from unlocking. I provided a technical explanation of the oven door lock function in the first image below. The second image shows the wiring diagram for the oven. The third image shows the location of components in the control area. You may be able to determine the cause of your failure using this information.

You can shut off the circuit breakers for the oven to completely disconnect electrical power and check for a wiring failure or a problem with the switches in that door lock circuit. I recommend that you check the wiring connections first.

If you need more help, reply with additional details and we will assist you further.

You can order parts from the Sears PartsDirect website if needed. Be sure that you disconnect electrical power to the oven before accessing internal components.

If you get to a point where you need to have a service technician diagnose and repair this failure, you can schedule one through this link: Sears Home Services .

Read More
Lyle W -
Sears Technician
January 03, 2012
A:

I have Kenmore oven model 665.72023102. I put it through self cleaning and at the end and after the cool down, the "E1 F5" message came up on the display. The door remains locked and and "locked" appears on the display - any advice?

Read More
Rob -
January 24, 2012
A:

That E1 F5 code indicates that the clock control board detects a problem with the oven door lock motor assembly. This makes sense since the oven door will not unlock after that clean cycle. You can UNPLUG the range and access that oven door lock motor assembly that is located on the back of the range (shown as Key 32 in the parts image below). Remove that back panel on the range to access that component. Check the wiring connections. If you find no wiring problems, then you will probably need to replace that part. You can order parts from the Sears PartsDirect.com website (see link below). The part number for that door lock motor assembly is W10107820. UNPLUG the range before accessing and replacing that component. If you still see that code after replacing the door lock assembly, then you may also need to replace the clock control board in the console. Reply with additional details if you need more help with this failure.

Read More
Lyle W -
Sears Technician
January 24, 2012
See more answers

Top Parts