Model #91141055591 KENMORE Built-In Oven, Electric

  • Control Panel
    3 Results
  • Door Lock Section
    3 Results
  • Door Section
    3 Results
  • Body Section
    3 Results
  • Wire Harness
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Pls provide downloads for manuals model # 91141055591 (Kenmore oven) and model # 72189941490 (microwave)

A:

ManageMyLfe.com is a great place to find your owner's manual and installation guides for appliances. I did some research and found the owner�s manual for the microwave. I have attached the link below. Your expert will follow up and verify this information shortly with the manual for the Kenmore oven. If you are having a specific problem please submit your question on the existing tread by click on the reply box below for your expert.

Read More
Anna T -
May 15, 2012
A:

I see Anna provided you with the owner's manual for the microwave. Unfortunately, the owner's manual for the Kenmore oven is not available for download. The manual can be purchased from Sears PartsDirect . I hope this helps.

Read More
Korinna S -
Sears Technician
May 15, 2012
See more answers
Q:

I have a kenmore wall oven #911.41055591. & I need to know why my control panel doesn't light up. I'm able to trun on the light but the control panel doesn't

A:

It is always a little frustrating when an appliance starts acting up on us. I'm sorry to hear that you are having some issues with your Kenmore Wall Oven. I did some research at Managemylife website and found an expert answer to a similar question that may help until your expert can respond. I have attached the link below so you can check it out. If you do decide to schedule service and have a qualified technician assist you, I have attached a link to SearsHomeServices.com. I hope the links below will help you out.

Read More
James -
February 29, 2012
A:

Since that oven light works, this indicates that you have the proper voltage supply provided to the oven that should power up that display. The wiring diagram for that oven is shown in the first image below. Since the light works, that circuit that is traced in yellow is apparently okay. The circuit that powers up the control is traced in red and green. The wire traced in red is actually black and the neutral wire traced in green is actually white in color. I recommend that you shut off the house circuit breakers to the oven to completely disconnect electrical power. You can access the clock control board in the console as shown in the second image. The third image shows the location of components in that control area. The 4th image shows the L1 connection (black wire) that is marked on that drawing in red. The neutral connection (N) is marked in green (actual wire color is white). I recommend that you check those wiring connections. Check the control board for a burned spot or obvious damage. If that control board is obviously damaged, then it will need to be removed and sent to Core Centric Solutions for repair. There is not a replacement part available for that control board but it can be repaired by that company. Here is a link for the website for that control board repair company: CoreCentricSolutions.com . That website has contact information so that you can arrange to send that control board off for repair. The repair will normally cost around $150.

If you see no apparent damage to that control board, then you will need to carefully check the live voltage supply going to that control board through the black and white wires using a volt/ohm meter. NOTE: You should only check that live voltage if you are completely confident in your technical ability to safely measure it. Wear proper safety equipment (electrical safety gloves and safety goggles) when completing that voltage check. Disconnect electrical power as soon as live testing is completed . If the control board is getting voltage but will not power up, then it will need to be repaired as described above.

This information should help you fix this oven failure. If you need more assistance, reply with additional details.

If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services .

Read More
Lyle W -
Sears Technician
March 01, 2012
A:

Here is the 4th image.

Read More
Lyle W -
Sears Technician
March 01, 2012
See more answers
Q:

I there a reset for my Kenmore wall oven model 911.41055591 that will not unlock after a cleaning cycle?

A:

The F2 error code indicates that the electronic oven control sensed an over temperature condition. If the oven actually overheated, you could have a stuck relay. If not, you could have a failed oven temperature sensor or a number of other problems. The second image below provides the technical information on this error code and information about the components. The first image has access information for the control. If you are able to shut off the breaker and access the control, you may be able to determine the cause of this problem and repair the oven yourself. I recommend that you check the resistance of the temperature sensor probe first and replace this part if necessary. You can order parts from the Sears PartsDirect website.

If you are not completely confident that you can safely access the control and properly diagnose the cause of this failure, I recommend that you call a service technician.

If you need more help, resubmit your question with additional details.

Read More
Lyle W -
Sears Technician
October 16, 2009

Top Parts