Model #9114012990 KENMORE Built-In Oven, Electric

  • Control Section
    3 Results
  • Wire Harnesses And Components
    3 Results
  • Door Section
    3 Results
  • Door Section
    3 Results
  • Body Section
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Kenmore Single oven Model # 9114012990 Display shows -F I- instead of clock and beeps. cannot turn it off

A:

I'm sorry that you are having some difficulties with your Kenmore Oven. I did a little research for you at Managemylife.com and found an expert answer to a similar question that may help until your expert can respond to your specific question. The link is attached below. If you decide to schedule service and have a qualified technician help you, I have also attached a link to Searshomeservices.com. I hope these links will help until your expert can respond.

Read More
James -
June 08, 2011
A:

Thank you for your question and I understand your concern.

The "F1" fault code means the oven control board has failed. The oven control board will have to be replaced to resolve the F1 fault code.

The oven control board will have to be removed and sent in for repair. The technician will have to come out and remove the oven control board. He will have it sent off to a rebuild center and they will repair the control like new. The control board will cost approximately $150.00 and the service fee will cost approximately $130.00 which includes the labor to remove and install the control board.

You can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
June 08, 2011
A:

Hi Joey S. do you think I could order the part and do it myself? Do you know what the part # for this oven is?

Read More
parnell -
June 24, 2011
A:

Hello Parnell. Joey is on vacation. If you can shut off the house circuit breaker for that oven and remove the control board (part 346062) in that console, then you can call Core Centric Solutions at 1-866-737-2244 and arrange to send them that control board for repair. To open that console, you may be able to release the control panel by removing the screws on that very top of that oven. After removing the screws on each side of the top of that control panel, you may be able to lift it up slightly to release it and fold it down. There may be screws on the bottom that need to be removed but I don't see any on the parts diagram. You can pull the oven out of the cabinet and remove the top cover over the controls if you cannot release that control panel. If you can get that control (KEY 16 in the image below) out of that console and have it repaired, then you may be able to fix this problem yourself. If you need more help, let us know.

Read More
Lyle W -
Sears Technician
June 24, 2011
See more answers
Q:

Why does my built-in oven not heat up to the temperature that it was set at?

A:

I would test the resistance of the oven temperature sensor probe first. The oven temperature sensor probe is located inside the oven cavity in the rear upper left hand corner or possibly in the rear upper right hand corner. It can be taken out and tested using an OHM meter. The oven temperature sensor should have a resistance measurement of 1100 ohms at room temperature. If the sensor measures approximately 1100 ohms, the oven control board will need to be replaced. If it does not measure 1100 ohms, replace the oven sensor. The oven sensor is part #WB21X5301 at the cost of $73.49

The oven control board is no longer available for ordering. The only way to get a working control board is to have a Sears technician remove the control and send if off for rebuilding. It will cost $130.00 to have a technician come out and service the range plus the cost of the control board.

It would not be cost effective to have the control board removed and rebuilt. I recommend replacing the wall oven rather than having the control board rebuilt.

Read More
Joey S -
Sears Technician
January 27, 2010
Q:

Why does my built-in oven not heat up to the temperature that it was set at?

A:

I would test the resistance of the oven temperature sensor probe first. The oven temperature sensor probe is located inside the oven cavity in the rear upper left hand corner or possibly in the rear upper right hand corner. It can be taken out and tested using an OHM meter. The oven temperature sensor should have a resistance measurement of 1100 ohms at room temperature. If the sensor measures approximately 1100 ohms, the oven control board will need to be replaced. If it does not measure 1100 ohms, replace the oven sensor. The oven sensor is part #WB21X5301 at the cost of $73.49

The oven control board is no longer available for ordering. The only way to get a working control board is to have a Sears technician remove the control and send if off for rebuilding. It will cost $130.00 to have a technician come out and service the range plus the cost of the control board.

It would not be cost effective to have the control board removed and rebuilt. I recommend replacing the wall oven rather than having the control board rebuilt.

Read More
Joey S -
Sears Technician
January 27, 2010