Model #9114012190 KENMORE Built-In Oven, Electric

  • Control Section
    3 Results
  • Wire Harnesses And Components
    3 Results
  • Door Section
    3 Results
  • Door Section
    3 Results
  • Body Section
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

ignitor clicking 9114012190 Kenmore Elec built-in oven

A:

Thank you for choosing Sears Parts Direct. I will be more than happy to help with your oven. Upon researching 9114012190; I show it is an electric wall oven.

We appreciate your business. Have a great day.

Read More
Jeff Wallace Jr -
Sears Technician
October 06, 2014
Q:

Oven heating problems 9114012190 Kenmore Elec built-in oven

A:

Thanks for the inquiry and for using SearsPartsDirect.com.
Due to the age of the wall oven, we are limited with the documentation we have, however, based upon the symptom you are experiencing, the oven sensor would be the first component to check. Typically, the oven sensors should have a resistance of about 1091 ohms at room temp. If the sensor checks out, the controller would be the next component. Usually the sensor will be defective in these circumstances. If the sensor is not working properly, it will cause the oven to not heat to the desired temperature or heat excessively past the desired temperature. The sensor more or less tells the controller when to power the elements. 
Unfortunately, it appears that the sensor, part number 334300 is no longer available for the unit. If needed, you could try running an online search for the part number to see if there are any still available, but that would be the only option I could foresee. If there was a newer sensor compatible with the old, the manufacturer would substitute it in place or the original, which has not occurred.
Hopefully this helps and let us know if we can be of any further assistance. Thanks for using SearsPartsDirect.com. 

Read More
Jeff Wallace Sr -
Sears Technician
February 05, 2014
Q:

can I replace the bake element 9114012190 Kenmore Elec built-in oven

A:

Thank you for contacting SearsPartsDirect.com with your question about your Kenmore Built-In Oven. I am so sorry to hear the bake element needs to be replaced. I know what an inconvenience it is when the oven isn’t working. I will be happy to help you with this.

 

SAFETY WARNING: Disconnect the power supply to the oven to prevent risk of injury or death from electrical shock. Since the oven is built into the wall, the easiest way to do this would be to turn off the breaker in the fuse box to your home. If you can access the power cord, unplug it as an additional precaution.

 

Start by removing the oven racks. There are a couple of screws that hold the bake element to the back wall of the oven. Remove those and then pull the element out of the back wall. Do not pull hard on the element. It is attached to wires that will need to be disconnected before you completely remove the element. Once you have released the wires, I recommend using pieces of electrical tape to keep the wires from retracting into the hole and falling behind the back wall of the oven and out of reach.

 

Once you have the old element removed, simply reverse the process to install the new element. Once the element has been installed, you can restore power to the oven.  

I have included the link for you to order the bake element, in case you haven’t done that yet.

 

Bake Element for Kenmore Built-In Oven Model 9114012190.

 

If you are not comfortable completing this repair yourself, you can have a Sears' technician complete the repair for you. To set up service please go to www.SearsHomeServices.com or call 1-800-469-4663.

 

I hope this answers your question. If I can be of further assistance please respond to this thread. Thank you for choosing Sears, we appreciate your business.

Read More
Rachel Morgan -
Sears Technician
October 02, 2013