Model #91136755590 KENMORE Slide-In Range, Gas

  • Door Section
    3 Results
  • Main Top Section
    3 Results
  • Door Lock Section
    3 Results
  • Top Burner Section
    3 Results
  • Oven Burner Section
    3 Results
  • Optional Backsplash
    3 Results
  • Body Section
    3 Results
  • Wire Harness And Components
    3 Results
Find part by diagram >

Question and Answers

Q:

How do I change my stove from Natural gas to propane?

A:

I can understand how important it is to have the right information for your range. The conversion kit instructions are usually included with the orifices in the kit. If you do not have a copy of it, finding one can be very difficult. However, I do have a set of our most common conversion kit instructions. This process should work for you unit as well. If you would like to download and view these, please click on this link: Kenmore Range LP Conversion. Also, I would suggest that you read the information on this link: LP conversion. This will provide some additional information that is not the instructions. If you don't feel comfortable doing this yourself, please click on the link to schedule service: Sears Home Services. Click on "Get Started" and follow the directions, click on the red "NEXT" button to continue. I hope this helps. Please feel free to let me know if you need further assistance. We are always here to help. Thank you for using ManageMyLife.com.

Read More
AnneJ -
Sears Technician
September 16, 2013
Q:

F3 Code on gas range

A:

A range is definitely something we depend on and when it begins to malfunction it can be a huge inconvenience. While you are waiting for an expert to respond, I have attached some helpful links below that may provide information to assist you with your question.

Read More
Alina F. -
January 10, 2012
A:

The F3 error code on this range indicates that the oven clock control board detects a problem with the temperature sensor probe circuit. The technical information on that code is shown in the first image below. The second image shows a wiring schematic and the third image has the wiring diagram for this range. I provided access information for the clock control board in that 4th image. I recommend that you shut off the house circuit breaker or remove the house fuse for the range to disconnect electrical power and access that sensor as shown in the 5th image. Check the resistance of that sensor using a volt/ohm meter as shown in this brief repair video: Oven Sensor Testing . You should measure around 1100 ohms through that sensor at room temperature. If the sensor is bad, it will need to be replaced. The part number for that sensor is WB21X5301. You can order that part from the Sears PartsDirect website. Here is a direct link for that part: Sensor . Be sure that you shut off the house circuit breaker to disconnect electrical power before accessing internal components and replacing that part.

If the sensor resistance is okay at room temperature, then you could still have a problem when it heats up according to your description of the problem. You may need to check the resistance of that sensor at operating temperature. The highest resistance that the sensor will normally measure will be about 2650 ohms when the oven is a the self clean temperature (over 700 degrees). If the resistance is over that reading when the oven is at 350 degrees or a similar operating temperature then the sensor probe will need to be replaced.

If that sensor is okay then you could have a wiring failure in that circuit or a bad clock control board. You can plug that sensor probe back in and check the resistance of the entire sensor circuit from the clock control board in the console. If that resistance in that circuit is high, then you can check the harness between the control board and the sensor for problems. The most suspect component in that sensor wire harness is the disconnect plug at the sensor probe.

If the resistance through that sensor circuit is normal when the control is displaying that F3 code then the clock control board will probably need to be removed and sent to Core Centric Solutions for repair. The replacement part for that control is no longer available. That is why it would need to be removed and sent for repair. Here is link for the website for Core Centric Solutions that has contact information: CoreCentricSolutions.com . The repair of that control board normally costs around $150.

This information may help you diagnose and repair the cause of that F3 failure in the range. If you need more assistance, reply with additional details.

Read More
Lyle W -
Sears Technician
January 12, 2012
A:

Here are the 4th and 5th images.

Read More
Lyle W -
Sears Technician
January 12, 2012
See more answers
Q:

Where can I access the wiring diagram for my Kenmore range model 911.36755590?

A:

I attached the wiring diagram to your e-mail because we are not able to send any images along with the answers at this time.

Read More
Joey S -
Sears Technician
December 31, 2009

Top Parts