Model #91136655590 KENMORE Slide-In Range, Gas

  • Main Top Section
    3 Results
  • Door Lock Section
    3 Results
  • Top Burner Section
    3 Results
  • Oven Burner Section
    3 Results
  • Backsplash
    3 Results
  • Body Section
    3 Results
  • Wire Harness And Components
    3 Results
  • Door Section
    3 Results
Find part by diagram >

Question and Answers

Q:

Ignitors on gas top burners not working

A:

I know how important it is to have your range working in order to cook meals. I was able to find a couple links that will provide information on the range burners not igniting. I attached the links below. An expert will respond shortly to provide you with information specific to your model. I hope this helps.

Read More
Jackie S -
March 08, 2012
A:

There may still be moisture on the electrodes. That would prevent them from sparking. Allow all of those electrodes to dry out completely and then see if they will spark again. It may take a day or two for those electrodes to completely dry out so that they will spark properly.

If they do not begin sparking and igniting the burners again, then you will probably need to have the range serviced by a technician. You could have a wiring failure or a bad spark module. Here is a link for the Sears website where you can schedule service online: Sears Home Services .

If you want to troubleshoot this problem further and try to repair it yourself, reply with additional details and we will assist you further.

Read More
Lyle W -
Sears Technician
March 09, 2012
A:

It has been almost a week since I cleaned the burners and they are still not sparking. Our maintenance man from work can help me if we can find out how you get to the "spark module". Can you provide me with a wiring diagram or step by step instructions on how to get to it. I guess it isn't that big of a deal. I have been just lighting it with my long lighter which is working fine for now.

Read More
Phyllis -
March 10, 2012
A:

That spark module should be in the location that is shown in the first image below. The second image shows the wiring diagram for that portion of the range. That information may help you locate and check that component and the wiring. Be sure that you UNPLUG the range before accessing internal components. If you need more assistance, reply with additional details.

Read More
Lyle W -
Sears Technician
March 10, 2012
See more answers
Q:

Range model 91136655590, right burner not sparking .

A:

I'm sorry that you are having some difficulties with your Gas Range. I did a little research for you at Managemylife.com and found an expert answer to a similar question that may help until your expert can respond to your specific question. The link is attached below. If you decide to schedule service and have a qualified technician help you, I have also attached a link to Searshomeservices.com. I hope these links will help until your expert can respond.

Read More
James -
May 11, 2011
A:

Thank you for your question and I understand your concern.

The electrodes do not normally ever need to be replaced unless the ceramic base/insulator is cracked or broken. If the ceramic insulator is not cracked or broken the electrode is likely Okay. If the ceramic insulator is cracked or broken it will either cause it to jump spark from the cracked area to the metal top instead of jumping spark between the electrode and burner. The base must have a good ground.

Make sure the cap and burner cap has a good ground connection to the top. There is chance the electrode wire connection may have come loose from the electrode or the voltage the electrode is jumping to ground through the spark igniter wire under the top.

You can remove the burner base and check the connection to the electrode by removing burner cap and the screws securing the burner base to the top. I added the instructions in the image below.

Read More
Joey S -
Sears Technician
May 12, 2011
See more answers
Q:

Where can I find information and details on how to replace the control valve on a Kenmore gas range model 911.36655590?

A:

There are not any formal instructions or procedures available for this particular repair on your gas range. This type of repair is normally performed by a technician. The gas line connections must be properly leak checked. The basic process involves shutting off the gas supply to the range and removing the gas lines that are connected to the control valve. The gas lines are typically connected with compression fittings that just need to be unscrewed. The valve would be removed and the new one installed. The gas lines would need to be connected to the new gas valve and leak checked after being properly tightened. The method for leak checking the connections would be to make a thick mixture of water and dish washing liquid. Coat all of the fitting with this solution and let it sit for about 10 minutes with the gas turned on and applied to the fittings. If a leak is present it will appear as bubbles on the fitting due to the detergent solution. Again, I recommend that a technician complete this repair but the general instructions on how to replace the valve are provided.

Read More
Lyle W -
Sears Technician
October 28, 2009

Top Parts

Recommended maintenance parts & accessories