Model #9113658811 KENMORE Slide-In Range, Gas

  • Main Top Section
    3 Results
  • Oven Body Section
    3 Results
  • Power Lock Section
    3 Results
  • Top Burner Section
    3 Results
  • Broiler & Oven Burner Section
    3 Results
  • Oven Body Door Section
    3 Results
  • Wire Harnesses And Options
    3 Results
  • Optional Rear Main Top Filler
    3 Results
  • Optional Vertical Trim Extension
    3 Results
Find part by diagram >

Question and Answers

Q:

Why does My Range beeper keep going off when I use the oven? 9113658811 Kenmore Kenmore gas range

A:

Thank you for your question and I understand your concern.

Generally speaking, when the electronic oven control/clock begins beeping, it would display a fault code in the display. If there is no fault code displayed when it begins beeping, then I would suspect a faulty electronic oven control.

The electronic oven control part #WB19X255  for Kenmore model 911.3658811 can be ordered from Searspartsdirect.

If the oven control is displaying a fault code, reply to this thread with the fault code for addition information.

 I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post. 

Read More
Joey S -
Sears Technician
October 16, 2013
A:

It gave an F1 code I unplugged it and left it off for a while Plugged it back in and it worked ok What does F1 indicate? Thanks for your first response

Read More
John -
October 16, 2013
A:

John: The F1 indicates a faulty electronic oven control if the F1 continues to display again after discconnecting and reconnecting the power source.

Read More
Joey S -
Sears Technician
October 16, 2013
See more answers
Q:

Oven not heating up!!!

A:

When I am having a problem with my appliance what I like to do is refer back to my owners manual because usually it provides me with lots of handy troubleshooting. I would highly recommend for you to review your owners manual. If you do not have yours I have managed to locate one here on the Manage My Life website. I attached the link below for you to view while you wait on your answer from an expert. I hope this can help you out with the problem you are having with your gas range.

Read More
Alina F. -
December 19, 2010
A:

Thank you for your question and I understand your concern. In order for the oven safety valve to open and allow gas to flow to the bake burner, the bake igniter must glow and it must pull enough current to cause the oven safety valve to open. Since you said the bake igniter is not glowing, the failure could be the igniter, oven safety valve, relay board or the oven control board.

If the broil igniter will glow and cause the gas valve to open, you could take the bake igniter out and replace it with the broil igniter and then see if the oven will heat up in bake. If it glows and causes the bake burner to operate, replace the igniter. NOTE: Disconnect the power cord from the power source before removing the broil and bake igniter.

You can order the igniter from Sears Parts direct and have it shipped to you. The part number is WB2X9154.

If it does not glow, I recommend calling a service technician to diagnose which component has failed. You may want to think about replacing the range rather than having it repaired.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
December 21, 2010
See more answers
Q:

Concers a Sears range model # 911.3658811. I have purchased a new control assy. It is a rev. 4. I have a rev. 3.

A:

Doing repairs by yourself can sometimes be frustrating. Especially when the new part makes no sense. A suggestion I have while your waiting on an expert response it to visit the SearsHomeServices website to schedule service. I have provided the link below. Good luck!

Read More
Jacqueline S -
September 10, 2010
A:

The heat anticipators were mostly used in wall ovens. I don't think this portion of the instruction sheet applies to your range.

I am sending you a wiring schematic of your range. Use the parts of the replacement instructions that apply to your range.

These controls were made to replace several different models and the installation instructions are confusing.

Read More
Jimmy K -
Sears Technician
September 11, 2010
See more answers