Model #9113652091 KENMORE Range (gas)

  • Main Top Section
    3 Results
  • Backsplash-8059090
    3 Results
  • Body Section
    3 Results
  • Oven Burner Section
    3 Results
  • Top Burner Section
    3 Results
  • Door Lock Section
    3 Results
  • Oven Door Section
    3 Results
  • Wire Harnesses And Options
    3 Results
  • Optional Rear Main Top Filler 8028790
    3 Results
  • Optional Vertical Trim Extension 8068690
    3 Results
Find part by diagram >

Question and Answers

Q:

Oven temp issue 9113652091 Kenmore Gas range

A:

Thank you for your inquiry on your Kenmore Range, Model: 911.3652091. From reviewing the details on your model, some ranges in this group of models will use the same ignitor for the broil and the bake burner. Others will use a different ignitor for the broil burner. Try the broil function if the range has a separate broil burner (most of these models do have a separate broil burner). If the broiler heats and works properly but the bake burner does not then you likely have a problem with the bake burner ignitor. In this situation you may be able to unplug the range then switch the bake and broil ignitors if they are exactly the same part to see if the bake burner will heat properly with an ignitor that is known to be good. If your range does not have the same ignitor then you will not be able to attempt this type of troubleshooting. If the broil ignitor is different than the bake ignitor, check the see if the bake ignitor is glowing when the bake burner is set to light. It will likely be glowing since your details seem to indicate that the oven was heating up to some extent. If the bake ignitor is glowing then the ignitor is still the likely failed component even though it is glowing. The resistance of the ignitor is not likely decreasing to a point where the required current can pass through the circuit to open the gas valve (or keep it open if the burner initially lights). Replacing the bake ignitor may fix your problem in this situation. Replacing the ignitor is not guaranteed to fix this problem. A bad control board or a problem with a temperature sensor probe can also prevent the oven from heating properly.

Safety Warning: Before beginning the repair, disconnect the direct power supply to the range to prevent the risk of injury or any electrical shock.

If you don’t feel comfortable or confident in this repair, then you can have it repaired at home by a sears technician. I have the included a link to the website: Sears Home Services or call 1-800-469-4663.

 

I hope this answered your question. Thank you for contacting SearsPartsDirect.com, and have yourself a wonderful day. 

Read More
Gerry 93 -
Sears Technician
June 22, 2015
A:

Thank you very much for your reply. The broiler burner seems to be working ok so I switched out the igniters, still have the same issue. I set the oven to preheat to 450. It alarmed when it was hot. The oven temperature is 270-280 depending on where I check it with an infrared thermometer. The display says it is at 450. Any other suggestions or is it time to call a repairman?

Read More
LARRY -
June 22, 2015
See more answers
Q:

oven temp 9113652091 Kenmore Gas range

A:

Hello glad to help.  Thank You for choosing Sears PartsDirect.com
 
I am sorry and do understand your frustration when there is trouble with the range.
 
Glad to help out.   Im  looking at your Kenmore Gas Range model number  9113652091.

If the problem is that the temperatures aren't setting correctly the only way to correct that is with an oven sensor/thermostat.  First though I would test my ignitors.

How to test gas ignitors for ranges:
 
1.  Unplug the oven from the wall for your safety.
 
2.  Lower the oven door.  Sometimes best to have more room and just remove it.
 
3.  Remove the oven racks from inside.  Remove the lower panel when testing the bake ignitor.
 
4.  Remove the burner shield by taking out the screws that secure it to ignitor first.
 
5.  Next take out the screws that hold the ignitor.  Pull the ignitor away from the oven wall.
    Unclip the wire connector.  If the wire connector is not accessible, remove the back rear
    panel to the oven, or remove the bottom storage drawer to access the wire connector.
 
6.  Get a multimeter to the lowest setting so you can measure the Ohms of resistance.  Calibrate
    the meter. Refer to your meters instructions 
 
7.  Place one of the terminals on the ovens bake ignitor's terminal with one of the multimeters 
    probes.  Then touch the other terminal with the other probe.
 
8.  Check the multimeter's display  If the meter does not move, displaying a resistance of any 
    numbers on the Ohms of resistance, there is no continuity.   If no continuity then the bake 
    ignitor is bad.

After you test the igniors and you find they are good.  I'd replace the oven sensor.

Oven sensor for model 911.3652091


Thank you for your understanding in this matter and I hope we can help you with your future questions and repairs. "Please resubmit" if there are any further questions or statements.  Thank you for choosing Sears and using our SearsPartsDirect.com.
 

Read More
Larry L -
Sears Technician
March 31, 2014
Q:

Replace gas stove top

A:

Its great that you are wanting to do some remodeling. Managemylife.com is always a great resource to find the answers to just about anything. Your expert will research your question and respond within two business days but usually sooner.

Read More
Joseph P. -
January 10, 2012
A:

Thanks

Read More
Tammy -
January 10, 2012
A:

I cross referenced all of the models that use that type of stove top. The white and the almond color are available but that chrome color is no longer available as a replacement part. I assume that you are looking for the chrome color. I searched all of our parts resources but I could not find a source that still has that part (WB62K5086) available. If you can use the white or the almond color, you can order one of those tops from the Sears PartsDirect website. The white color top is part number WB62K5087. The almond color top is WB62K5088.

If you need more help, reply with additional details and we will assist you further.

Read More
Lyle W -
Sears Technician
January 12, 2012
See more answers

Top Parts