Model #9113548813 KENMORE Drop In, Gas

  • Control Panel
    3 Results
  • Main Top
    3 Results
  • Burner
    3 Results
  • Wire Harnesses And Options
    3 Results
  • Body
    3 Results
  • Oven Door
    3 Results
Find part by diagram >

Question and Answers

Q:

Why is my Kenmore range displaying F2 & F3 error codes?

A:

The F2 & F3 error codes both mention the temp sensor. The temp sensor is mounted inside the oven cavity & regulates the oven set temperature. If the temp sensor fails the oven could overheat. This is what generates the error codes. I recommend having the temp sensor checked with an ohm meter, at room temperature the sensor should ohm out at approx 1100 ohms. If you decide to replace the range I recommend going to www.sears.com to find the right size range for your needs.

Read More
biker dave -
Sears Technician
July 16, 2009
A:

I own a Kenmore 30" Drop In Range, and the model number is 911.4554591. I kept getting an F2 or F3 code. I replaced the Oven Heat Sensor and the stove worked fine for one day. All of a sudden it starting giving the F2 code again. Can you help?

Read More
Ben -
May 31, 2015
See more answers
Q:

Kenmore drop in oven

A:

The oven not working can be very concerning. I found some information for you that I am hoping will be able to help you with the oven. I am adding the link below to help you with your question while you wait for your expert response. It may take 24-48 hours. I do hope that everything works out with the oven.

Read More
Marc -
December 30, 2012
A:

That link for a previous answer that Marc posted in the above response covers a similar problem. Check to see if the broil burner works. This will verify that you have a good gas supply provided to the oven safety gas valve and that the control works in the broil mode. If the broiler works, you can shut off the house circuit breaker for the range and switch the bake and broil igniters. See if that bake burner works with those igniters switched. If it does, then replacing the bad igniter should fix this problem.

You could have a bad igniter, a problem with the safety gas valve or a failed electronic control board that would prevent the oven burner from igniting. Here is a link for a brief video that shows how the ignition system works on that range: Gas Ignition Operation . I recommend that you check to see if that igniter is glowing when the oven is set in the bake mode. If the igniter is not glowing, then I recommend that you shut off the house circuit breaker for the range to disconnect electrical power and check the resistance through the safety gas valve using a volt/ohm meter. You should measure about 1.5 ohms of resistance through that component. If the safety gas valve is bad, then you will normally need to replace that valve and the igniter at the same time. I recommend that you have a service technician repair that type of problem. You can schedule service through this link: Sears Home Services .

If you find the cause of the problem and want to fix this problem yourself, you can order parts from this page: Kenmore Range Model 911.3548813 Parts . Be sure that you shut off the house circuit breaker for the range to disconnect electrical power before accessing and replacing internal components.

If you replace the safety gas valve, be sure that you properly seal and leak check the gas line connections.

These tips may help you fix that oven heating problem in the range. If you need more assistance, reply with additional details.

Read More
Lyle W -
Sears Technician
January 02, 2013
See more answers
Q:

How can I get a Kenmore gas range wiring diagram?

A:

Getting the wiring diagram on the Kenmore range will definitely help in replacing the electronic control panel on this range. An expert will research and respond with additional information within two business days.

Read More
Anna T -
December 05, 2012
A:

The wiring diagram and technical information for this older Kenmore gas range is on microfiche. I posted a wiring diagram in the first image below. The second image shows a drawing of the back side of the control board. I marked the wiring connections with wire colors. There should be a jumper wire (probably black) that runs from the TT2 spade to the TT5 spade to supply the ignition circuits with L1 line power. This information should help you wire up that control board. If you need more help, reply with additional details and we will assist you further.

If you get to the point where you need to have a service technician install that control board, you can schedule service through this link: Sears Home Services .

Read More
Lyle W -
Sears Technician
December 07, 2012
A:

I really appreciate this. If this isn't helpful I will contact Sears Home Services. I plan that it will be fixed next week. Thanks so much Lyle - have a nice holiday season

Read More
Ginny -
December 07, 2012
See more answers