Model #91133213100 KENMORE ELITE Counter Unit, Gas

  • Maintop
    3 Results
  • Burner Section
    3 Results
Find part by diagram >

Question and Answers

Q:

Replacing igniter on a Kenmore 36" gas cooktop.

A:

Having a properly working cook top is very important. I found some information for you that I am hoping will help you until your expert answers your question. I am adding the link below to help you with your question while you wait for your expert response. It may take 24-48 hours. I do hope that this will help you with the cook top.

Read More
Marc -
October 17, 2012
A:

Thank you for your question and I understand your concern.

All 4 surface igniter should spark when ever any one burner knob is rotated to the lite position. If the two left side burner igniters do not spark when any of the 4 burner knobs are rotated to the lite position, this would be a very uncommon failure. The surface ignition system consists of the igniters, burner switches, wires connecting the each igniter to the spark module and the spark module. See image below. The image also has the wiring diagram and wiring diagram along with instructions for removing the top. NOTE: Disconnect the power cord from the power source before servicing.

The electrode will likely have a small clip under the top to remove before the electrodes can be removed.

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Read More
Joey S -
Sears Technician
October 18, 2012
A:

For the question I asked in re changing replacing an igniter on a Kenmore 36" gas cooktop, the specific model of my cook top is 911.33219100. It appears that all I have to do is remove the two screws in the burner top which will allow the igniter to be accessed from the bottom. However, I am hesitant to do anything until I get some expert advise. Thanks, Jim O'Rear.

Read More
James -
October 18, 2012
A:

James: In order to just access and replace the electrode all you should need to do is remove the take the screws out securing the burner base and lift it up. The electrode will have C-clip to slide off the base of the electrode and then disconnect the wire connection and lift the electrode out. See the image I added my previous answer is needed.

Read More
Joey S -
Sears Technician
October 18, 2012
See more answers
Q:

Couldn't find a replacement part for the wire harness for KENMORE Gas Cooktop

A:

Having the cooktop working to make your favorite meals is important. I found the burner wire harness for your model. I am adding the link below for the wire harness for you. I do hope that this will help you until your expert answer your question. I do hope all goes well.

Read More
Marc H -
June 08, 2012
A:

Thank you for help. But that harness does not goes directly to the igniters. I have ordered exactly that part but it does not fit anywhere. I think it was mistakenly put online. The Sears customer service couln't help and advised me to get on :managemylife" site :)

Read More
Andrew -
June 08, 2012
A:

Thank you for your question and I understand your concern.

I must assume the spark igniter wire harness will be part of the burner wire harness assembly because the parts list does not show just the harness for the electrodes. The wire harness assembly#WB18T10072 for Kenmore cook top 911.33213100 can be ordered from Sears Parts Direct. The link I added will show a picture of the wire harness assembly.

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Read More
Joey S -
Sears Technician
June 11, 2012
A:

Joe, thank you for response. I did order the WBT18T10072 but there were no connectors for the igniters. So that part does not have wires that I was looking for.

Read More
Andrew -
June 11, 2012
A:

Andrew: I would have thought the harness part number I provided would have had the electrode leads included in the wire harness assembly. I suggest calling Sears parts and have the part researched for the correct part number for the electrode wire leads. I have no other suggestions.

Read More
Joey S -
Sears Technician
June 11, 2012
A:

Well, that is very interesting. I did speak with Sears parts representative. He couldn't find that harness on drawings and advised me to go online www.managemylife.com and ask expert :-)

Read More
Andrew -
June 11, 2012
A:

Andrew: Sears Parts will need to find the part number of the electrode wires. They have the means and source of doing so.

Read More
Joey S -
Sears Technician
June 11, 2012
See more answers
Q:

How do I install a gas cook top igniter?

A:

Once you remove the two screws from the burner base, it should lift straight up and off of the top of the cook top. It is likely that a build-up of residue from spills is causing the burner base to stick to the cook top. You may be able to break the burner base free with more force or you may need to pry up slightly with a small flat tip screw driver to break the burner base free and remove it.

Read More
Lyle W -
Sears Technician
August 18, 2009
A:

911-3302191 where can i find a gas valve part no for this model

Read More
Anonymous -
February 12, 2012
See more answers

Top Parts