Model #91132285890 KENMORE Counter Unit, Gas

  • Main Top
    3 Results
  • Wire Harnesses And Components
    3 Results
  • Burner
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

What is BTU of the burners 91132285890 Kenmore 30" gas counter unit

Q:

How do I know if I need a 'spark module' or an 'electrode' for my Kenmore model 911-32285890 gas range?

A:

When an appliance suddenly stops working it can cause an inconvenience in your home. While you are waiting for an expert to respond, I have attached a helpful link below that may provide information to assist you with your question.

Read More
Yadira B -
January 30, 2013
A:

Check to see if all of the electrodes spark when the other burners are turned to the "light" position. If the igniters spark when all of the other burner control valves are turned to the "light" position then you probably have a bad burner switch (Key 323 in the parts image below).

When one burner switch is turned on, all of the electrodes on the burners should spark at the same time. If just that one switch is bad, then that is the only component that needs to be replaced. If the electrode on that burner won't spark even when a different burner is turned on and all of the other electrodes spark properly, then the electrode may also need to be replaced.

If none of the burners spark when any of the burners are turned to the "light" position then the range may not have electrical power or you may need to replace the spark module.

You can order parts from this page: Kenmore Cooktop Model 911.32285890 Parts . Be sure that you unplug the cooktop or shut off the house circuit breaker to disconnect electrical power before accessing internal components and replacing parts.

These tips may help you fix that problem in your cooktop. If you need more assistance, reply with additional details.

If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services .

Read More
Lyle W -
Sears Technician
January 31, 2013
A:

Here is the image.

Read More
Lyle W -
Sears Technician
January 31, 2013
A:

How do I get to, and replace the #323 valve switch or the #154 electrode? Are there 4 valve switches on a 4 burner stove?

Read More
ken -
January 31, 2013
A:

There is one valve switch on the top of each burner control valve. There is one electrode per burner. You would need to unplug the cooktop or shut off the house circuit breaker to disconnect electrical power. Shut off the gas supply and pull the cooktop out of the counter. You can use the installation manual as a guide for that process. You would then need to remove the grates burner heads and burner pans. You would then need to pull up the cooktop to access the burner switch and the electrode. I hope that these general instructions help. If you need more assistance, let us know.

Read More
Lyle W -
Sears Technician
January 31, 2013
See more answers
Q:

How do I adjust the flame on a cook top?

A:

A qualified installer should convert the cook top from natural gas to LP gas. Improper conversion can result in a dangerous situation.

The installation instructions provide the installer with the guidelines for converting the cook top to LP gas. Here is a link for the installation instructions for this cook top: Installation Instructions . With the gas supply shut off, the pressure regulator cap needs to be flipped to the LP position as shown on page 7 of the installation instructions.

If the LP orifices did not come with the cook top, you will need to order these orifices from the Sears PartsDirect website. Use the full model number of 911.32285890 (which should be the actual model number of your cook top) to order the correct orifices. According to the parts diagram for this cook top, you should need one small LP orifice (part WB28K5087) for the right rear burner and 3 medium LP orifices for the other burners (part WB28K145).

Once the cook top is properly converted by a qualified installer, the burners should work properly.

If you have already completed the conversion properly according to the guidelines in the installation guide, I recommend that you shut off the gas supply and recheck the position of the regulator cap and make sure that the proper orifices are installed on the burners. If you still have trouble then the cook top will likely need to be serviced by a technician.

Read More
Lyle W -
Sears Technician
March 10, 2010

Top Parts