Model #91130465791 KENMORE Wall Oven, Gas

  • Control Section
    3 Results
  • Wiring Components
    3 Results
  • Burner Section
    3 Results
  • Burner Section
    3 Results
  • Body Section
    3 Results
  • Door Section
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Calibrate Kenmore oven after new probe

A:

I understand that you are wanting to calibrate your oven. I have taken some time to research your question here on the Manage My Life website and I noticed that someone else had asked a similar question with a posted response from an expert. I attached the link below for you to view while you wait on your expert response. I hope the link that I have provided you is helpful.

Read More
Alina F. -
December 11, 2010
A:

I am sending you an image showing how to calibrate the temperature of your oven. This information is in the owners manual of the oven. You can get a copy of the owners manual free at [www.managemylife.com].

Read More
Jimmy K -
Sears Technician
December 13, 2010
See more answers
Q:

How do I Calbrate oven after installing new probe?

A:

I understand that you are wanting to calibrate your oven. I have taken some time to research your question here on the Manage My Life website and I noticed that someone else had asked a similar question with a posted response from an expert. I attached the link below for you to view while you wait on your expert response. I hope the link that I have provided you is helpful.

Read More
Alina F. -
December 11, 2010
A:

I am sending you an image showing how to calibrate the temperature of your oven. This information is in the owners manual of the oven. You can get a copy of the owners manual free at [www.managemylife.com].

Read More
Jimmy K -
Sears Technician
December 13, 2010
See more answers
Q:

Kenmore wall oven 91130465791 has error code F3

A:

A wall oven malfunctioning at this time of year is definitely disappointing, I'm sorry to hear that you are having problems. I was able to find some information on the meaning of that error code on Manage my life. I have posted the link below. Hope it helps!

Read More
Maira -
December 09, 2010
A:

As noted in the link for a previous answer provided by Maira, the F3 error code indicates that you have a problem with the oven temperature sensor circuit.

I recommend that you shut off the circuit breaker and check the resistance of the oven temperature sensor probe first. The first image below shows how to access this component. You can measure the resistance of that component using a volt/ohm meter. It should measure around 1100 ohms at room temperature (around 72 degrees). If the resistance is way off (by more than 100 ohms) then the sensor probe (part WB21X5301) will need to be replaced. Here is a Sears PartsDirect.com link for that part: Sensor .

Since the F3 occurs when the oven is heated up, the sensor may be okay at room temperature. It may increase the resistance too much when it is heated up. The F3 will occur when the resistance is above 2800 ohms or below 900 ohms. A technician would normally heat up the sensor probe with a heat gun (hair dryer) and see if the resistance increases over the 2800 ohms when the sensor probe is hot if necessary. You may or may not need to conduct this extra test.

I provided additional technical information about this failure in the second image below. It has information on testing the wire harness and the control board. It also give access information for the control board. You may need to use this information to diagnose and repair this failure. NOTE: Be sure that you shut off the circuit breaker to disconnect electrical power before accessing internal components. Shut off the gas supply as well.

This information should help you resolve this problem in your oven. If you need parts, you can order them from the Sears PartsDirect website.

If you need more help, reply with additional details.

This intermittent problem could be difficult to diagnose and repair. If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Lyle W -
Sears Technician
December 11, 2010
See more answers