Model #91130169791 KENMORE Wall Oven, Gas

  • Burner
    3 Results
  • Body
    3 Results
  • Control
    3 Results
  • Door
    3 Results
  • Wiring Components
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

kenmore door lock/ shut off 91130169791 Kenmore 24

A:

Thank you for choosing Sears Parts Direct. I will be happy to help with your range. Upon researching model 91130169791; I found information on error code F3. I posted the link below.

Thank you for choosing Sears. We appreciate your business. Have a great day.

Read More
Jeff Wallace Jr -
Sears Technician
January 06, 2015
A:

Thank you for choosing Sears Parts Direct. I will be happy to help with your range. Upon researching model 91130169791; I found information on error code F3. I posted the link below.

Thank you for choosing Sears. We appreciate your business. Have a great day.

 

Read More
Jeff Wallace Jr -
Sears Technician
January 06, 2015
See more answers
Q:

Oven preheats then shuts down 91130169791 Kenmore 24" gas built-in oven

A:

Hello glad to help.  Thank You for choosing Sears PartsDirect.com
 
I am sorry and do understand your frustration when there is trouble with the gas oven.
 
Glad to help out.   Im  looking at your Kenmore model number 911.30169791.

I know  you say the ignitor is still on but it may not be discharging as it should.   It can be on and still be bad so you need to take a meter to it and test it.

How to test gas ignitors for ranges:
 
1.  Unplug the oven from the wall for your safety.
 
2.  Lower the oven door.  Sometimes best to have more room and just remove it.
 
3.  Remove the oven racks from inside.  Remove the lower panel when testing the bake ignitor.
 
4.  Remove the burner shield by taking out the screws that secure it to ignitor first.
 
5.  Next take out the screws that hold the ignitor.  Pull the ignitor away from the oven wall.
    Unclip the wire connector.  If the wire connector is not accessible, remove the back rear
    panel to the oven, or remove the bottom storage drawer to access the wire connector.
 
6.  Get a multimeter to the lowest setting so you can measure the Ohms of resistance.  Calibrate
    the meter. Refer to your meters instructions 
 
7.  Place one of the terminals on the ovens bake ignitor's terminal with one of the multimeters 
    probes.  Then touch the other terminal with the other probe.
 
8.  Check the multimeter's display  If the meter does not move, displaying a resistance of any 
    numbers on the Ohms of resistance, there is no continuity.   If no continuity then the bake 
    ignitor is bad.

With everything else working right.   It sounds like  you need a new ignitor or the possibility that the chip inside the control board that takes care of the oven is going bad.  

If you have further questions please let me know.
Thanks for choosing Sears PartsDirect.com

Read More
Larry L -
Sears Technician
February 04, 2014
A:

Thanks Larry, This is a second home and week will be there in a week. I'll ohm it out then. Thanks again

Read More
Steve -
February 06, 2014
See more answers
Q:

Built In Oven Unit Keeps Beeping and showing F2 on Display Screen

A:

Thank you for your question. I understand your concern about the error code. This error code indicates the oven got to hot (see attachment below). This can be due to a failed sensor, control board or if one of the elements shorted. I hope this helps you. If you would like more assistance, reply to this thread and I will be glad to assist you further. If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services.  

Read More
Scott D -
Sears Technician
November 27, 2013
A:

Thank you for your reply. I will see to having it repaired in the near future.

Read More
Nadine -
November 27, 2013
A:

Nadine, thank you for using Manage My Life.

Read More
Scott D -
Sears Technician
December 02, 2013
See more answers